JL Audio SB-MIN-COOP/8W7 ConGRatulatIons!

d e ta I l

ConGRatulatIons!

You have completed the installation for this model!

Enjoy your new Stealthbox®!

Please refer to the Power Recommendation section for an

amplifier recommendation and basic set-up help.

s t e P 5

Set the enclosure into place with the Socket Cup Set Screw

going through the holes drilled in steP 4. Install the

supplied hardware on the Socket Cup Set Screw to secure

the Stealthbox®. There should be a Hex Head Nut, Split Lock

Washer and, Flat Washer on each Socket Cup Set Screw.

Only snug each set of hardware initially then, tighten each

set after they are both snug.

s t e P 4

CAUTION

Before drilling, always make sure that you are not

going to be drilling into any gas lines, brake lines,

transmission lines, electrical wiring, exhaust systems

or anything else that might cause a reduction in your weekly

pay. Always wear eye protection when drilling.

Using a 1/2” drill bit, drill where the impressions were made in

the wax squares.

s t e P 3

Place the Stealthbox® into the vehicle in the orientation that

it will ultimately remain in. The speaker terminals should be

on the side facing towards the front of the vehicle. Once in

place, press down on the enclosure so that the two 3/8-16x

2 1/4” Socket Cup Set Screws make depressions in the 3” x 3”

wax squares. If the Socket Cup Set Screws do not make the

depressions in the wax squares, back them out further and

repeat the procedure untill they do. Once the locations are

marked, Back out the Set Screws so that approximately 1-1

1/2” is exposed.

Page 2 • JL Audio, Inc 2008

STEALTHBOX WALL

THREADED INSERT

VEHICLE SHEET METAL

FENDER WASHER SOCKET CUP SET SCREW

LOCK WASHER

FLAT WASHER

HEX BOLT

SB-MIN-COOP/8W7 INSTR_SKU# 011280

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign

patents pending. For more detailed information please visit us online at www.jlaudio.com.

(954) 443-1100

www.jlaudio.com

10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA

I n C lu d e d H a R d W a R e

2) 3/8” Flat Washer 2) 3/8” Split Lock Washer

2) 3/8-16x 2 1/4” Socket cup Set Screw 2) 3/8” Hex Nut

s Pe C I F I C a t I o n s

Enclosure Type: Acoustic Suspension (sealed)

Driver Type: 8W7 (2)

Nominal Impedance: 3 Ohm (each)

Continuous Power Handling: 500 Watts (each)

P o W eR R e C o m m e n da tI o n

JL Audio recommends using a high quality amplifier such as the JL Audio HD750/1.

The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the HD750/1

when being used to power your Stealthbox®.

The JL Audio HD750/1 is a very versatile audio component. Please consult the owner’s manual for even more

detailed information about installing and tuning this amplifier.

m I d /H I G H F R e q u e n C Y d R I v eR F I t m e n t

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of your vehicle.

Front Speaker Size / Location: 6 1/2”- Front Doors

Fits JL Audio Models: TR650-CSi, TR650-CXi, VR650-CSi, VR650-CXi, XR650-CSi, XR650-CXi,

C5-650, C5-650x & ZR650-CSi

Rear Speaker Size / Location: 6inch x 9inch - Rear sides

Fits JL Audio Models: *TR690-TXi & *VR690-CXi

*Smaller speakers would al so fit using custom adapt ors

*CAUTION*