Limited Warranty

Johnson Controls Unitary Products (hereinafter “Company”) warrants this product to be free from defects in factory workmanship and material under normal use and service and will, at its option, repair or replace any parts, without charge, subject to the exclusions below, that prove to have such defects according to the terms outlined on this warranty. This warranty covers only the equipment described by the Product Model Number and Serial Number on the equipment or listed on the Warranty Registration Card and applies only to products installed in the United States or Canada.

FOR WARRANTY SERVICE OR REPAIR:

Contact the installer or a Company dealer. You may find the installer’s name on this page or on the equipment. You can also find a Company dealer online at www.yorkupg.com. For help finding a servicing dealer, contact: Johnson Controls Unitary Products, Consumer Relations, 5005 York Drive, Norman, OK 73069. Or, by phone 877-874-7378. All warranty service or repair will be performed during regular business hours, Monday through Friday 9:00am-5:00pm.

Product Model No.__________________________________

Installation Date_________________________________________

Unit Serial No._____________________________________

Installing Dealer_________________________________________

FOR PRODUCT REGISTRATION: For your benefit and protection, return the Warranty Registration Card to Company promptly after installation. This will ini- tiate the warranty period and allow us to contact you, should it become necessary. For this warranty to apply, the product must be installed according to Com- pany recommendations and specifications, and in accordance with all local, state, and national codes; and the product must not be removed from its place of original installation. The warranty period for repair or replacement parts provided hereunder shall not extend beyond the warranty period stated below. In the absence of a recorded Warranty Registration Card, the warranty period will begin upon product shipment from Company. If you are unaware of the date the warranty became effective, contact Company at 877-874-7378 or visit www.upgproductregistration.com. You can register your product online at www.upgpro- ductregistration.com or by returning the Warranty Registration Card on the back page of this packet.

HEAT EXCHANGER WARRANTY ADDITIONAL TERMS: Company warrants the heat exchangers (primary and/or secondary, if applicable) in this product to be free from defects in factory workmanship and material under normal use and service and will at its option, repair or furnish a replacement heat exchanger, either new or reconditioned that meets the intended fit, use and function of the original heat exchanger. Alternatively, Company may, at its option, extend a replacement allowance to be applied toward the purchase of a new furnace marketed by Company. The exact amount of the allowance will be determined at the discretion of Company, based upon current market conditions, but in no case shall this allowance exceed thirty (30) percent of the original consumer pur- chase price of the furnace, excluding such items as ductwork, wiring, piping, and installation costs. Company shall have no responsibility hereunder for instal- lation, shipping, handling or other charges except as specifically provided herein.

The warranty period in years, depending on the part and the claimant, is as shown in the chart below.

 

 

HEAT EXCHANGER

 

FURNACE TYPE

Residential Applications

Non-Residential

PARTS

 

Original Owner

 

Subsequent

Applications

 

 

 

Owner

 

 

 

 

 

 

GG8S,GGLS

20

 

N/A

10

5

TM8X,TMLX,TM8T,TMLT,TM8V,TMLV,TG8S,TGLS

20

 

N/A

10

5 or 10†

GG9S

Lifetime

 

20

10

5

TM9V,TM9T,TM9X,TG9S

 

 

 

 

 

TP9C,TP8C,TPLC,TM9M,TM8M,TMLM,YP9C,YP8C,YPLC,YM9M,YM8M,YMLM

Lifetime

 

20

10

5 or 10†

CP9C,CP8C,CPLC,CM9M,CM8M,CMLM,LP9C,LP8C,LPLC,LM9M,LM8M,LMLM

 

 

 

 

 

To qualify for the extended 10-year parts warranty, the unit must be registered online at www.upgproductregistration.com within 90 days of installation for replacement or 90 days of closing for new home construction. In some states, registration is not required, but proof of installation may is required to qualify for the 10-year parts warranty. Guardian Brand products have a 5-year compressor and 5-year parts warranty and are not eligible for the 10-year parts warranty.

Company strongly recommends regular periodic preventative maintenance on this equipment. The person most familiar with the equipment in your HVAC sys- tem is a Company dealer. The Company dealer can ensure your maintenance program meets the conditions of the "Company Warranty", maximize the effi- ciency of the equipment, and service your unit within the mandated guidelines with regard to unlawful discharge of refrigerants into the atmosphere.

EXCLUSIONS:

This warranty does not cover any:

1.Shipping, labor, or material charges or damages resulting from transportation, installation, or servicing.

2.Damages resulting from accident, abuse, fire, flood, alteration, or acts of God (tampering, altering, defacing or removing the product serial number will serve to void this warranty).

3.Damages resulting from use of the product in a corrosive atmosphere.

4.Damages resulting from inadequacy or interruption of electrical service or fuel supply, improper voltage conditions, blown fuses, or other like damages.

5.Cleaning or replacement of filters or damages resulting from operation with inadequate supply of air or water.

6.Damages resulting from failure to properly and regularly clean air and/or water side of condenser and evaporator.

7.Damages resulting from: (I) freezing of condenser water or condensate; (II) inadequate or interrupted water supply; (III) use of corrosive water; (IV) fouling or restriction of the water circuit by foreign material or like causes.

8.Damages resulting from use of components or accessories not approved by Company (vent dampers, etc.).

9.Increase in fuel or electric cost.

This warranty is in lieu of all other warranties, expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose.

Some states do not allow the disclaimer of implied warranty, so that the above disclaimer may not apply to you. Some states only allow a partial limitation on implied warranties to limit the duration of implied warranties to the duration of the express warranty. In such states, the duration of implied warranties is hereby expressly limited to the duration of the express warranty on the face hereof. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

In no event, whether as a result of breach of warranty or contract, tort (including negligence), strict liability, or otherwise, shall Company be liable for special, incidental, or consequential damages, including but not limited to loss of use of the equipment or associated equipment, lost revenues or profits, cost of substitute equipment or cost of fuel or electricity. The above limitations shall inure to the benefit of Company’s suppliers and subcontractors. The above limitation on consequential damages shall not apply to injuries to persons in the case of consumer goods.

Company does not assume, or authorize any other person to assume for Company, any other liability for the sale of this product. Some states do not allow the exclusion or limitation of incidental or consequently damages, so the above limitation may not apply to you.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

Subject to change without notice. Printed in U.S.A.

356486-UUM-H-0609

Copyright © 2009 by Johnson Controls, Inc. All rights reserved.

Supersedes: 356486-UUM-G-0409

Johnson Controls Unitary Products

5005 York Drive

Norman, OK 73069

Page 6
Image 6
Johnson Controls 356486-UUM-H-0609 warranty Limited Warranty, Exclusions

356486-UUM-H-0609 specifications

Johnson Controls 356486-UUM-H-0609 is a cutting-edge solution designed for modern heating, ventilation, and air conditioning (HVAC) systems. This particular model is engineered to enhance energy efficiency and optimize system performance across various applications. One of its main features is the advanced microprocessor control, which allows for precise temperature regulation, improved system efficiency, and adaptive learning capabilities. This technology significantly reduces energy consumption, leading to lower utility bills.

The unit incorporates state-of-the-art communication protocols, which facilitate seamless integration with existing building management systems. By supporting protocols such as BACnet, Modbus, and LonWorks, the 356486-UUM-H-0609 can communicate effectively with a wide range of devices, ensuring compatibility in diverse environments. This flexibility is crucial for facilities managers looking to enhance or upgrade their systems without complete overhauls.

Another standout characteristic of the Johnson Controls 356486-UUM-H-0609 is its user-friendly interface. The intuitive touchscreen display provides real-time feedback and allows operators to adjust settings with ease. The interface includes customizable features that enable users to create specific scheduling and control options to meet unique requirements, thereby improving overall user experience.

The device also prioritizes reliability and robustness, incorporating high-quality materials and components designed to withstand a variety of environmental conditions. Its durable construction minimizes wear and tear, extending the lifespan of the equipment while reducing maintenance costs.

Moreover, the 356486-UUM-H-0609 leverages innovative sensor technology to monitor temperature, humidity, and air quality continuously. This data-driven approach allows for automated adjustments based on real-time conditions, ensuring optimal comfort while significantly improving indoor air quality.

In summary, the Johnson Controls 356486-UUM-H-0609 is an advanced HVAC control solution built to meet the demands of the modern world. With its powerful microprocessor control, flexible communication capabilities, user-friendly interface, and robust design, it sets a new standard for energy efficiency and operational excellence in building management systems. This model is ideal for facilities seeking to elevate their HVAC performance while ensuring sustainability and comfort.