813196-UUM-C-0412

COOLING CONSERVATION

To comfortably cool your home, your air conditioner must remove both heat and humidity. Don’t turn your system off even though you will be away all day. On a hot day, your system may have to operate between 8 to 12 hours to reduce the temperature in your home to a normal comfort level.

Keep windows closed after sundown. While the outdoor temperature at night may be lower than indoors, the air is generally loaded with mois- ture which is soaked up by furniture, carpets, and fabrics. This moisture must be removed when you restart your system.

The hotter the outside temperature, the greater the load on your sys- tem. Therefore do not be alarmed when your system continues to run after the sun has set on a hot day. Heat is stored in your outside walls during the day and will continue to flow into your home for several hours after sunset.

Use your kitchen exhaust fan when cooking. One surface burner on “HIGH” requires one ton of cooling. Turn on your bathroom exhaust fan while showering to remove humidity. However, exhaust fans should not be run excessively. It would decrease efficiency by removing condi- tioned air.

You can also help your system in the summer by closing drapes or blinds and by lowering awnings on windows that get direct sunlight.

CARE OF SYSTEM

It is strongly recommended that regular periodic preventative mainte- nance be performed on this equipment. The person most familiar with the equipment in your H.V.A.C. system is a dealer. The dealer can ensure your maintenance program meets the conditions of the War- ranty”, maximize the efficiency of the equipment, and service your unit within the federally mandated guidelines with regard to unlawful dis- charge of refrigerants into the atmosphere.

COIL CARE

Keep the outdoor unit free of foliage, grass clippings, leaves, paper, and any other material which could restrict the proper air flow in and out of the unit. The coil may be vacuumed to remove any debris from between the fins. If the coil becomes excessively dirty, turn the main disconnect switch to “Off” and wash the coil with your garden hose. Avoid getting water into the fan motor and control box. Flush dirt from base pan after cleaning the coil.

SERVICE CALLS

There are a few instances where the user can avoid unnecessary ser- vice calls. If unit stops functioning properly check the following items before calling your servicing dealer:

1.Indoor section for dirty filter.

2.Outdoor section for leaf or debris blockage. Eliminate problem, turn off the thermostat for 10 seconds and attempt start. Wait 5 minutes. If system does not start, call your servicing dealer.

Your system contains environmentally friendly refrigerant R-410A, which operates at high pressures. You may be in danger if you try to make an attempt to repair your unit. Please contact your local dealer.

FILTER CARE

Inspect the air filter(s) at least once a month. If they are dirty, wash reusable filters with a mild detergent per manufacturer’s recommenda- tions. Replace disposable filters with new filters. Install the clean filters with “air flow” arrow in the same direction as the air flow in your duct. Filters should be clean to assure maximum efficiency and adequate air circulation.

CLEARANCES

The minimum clearances shown below must be maintained should any patio or yard improvements be done around the outdoor unit.

10" Clearance Coil Area

60" Overhead Clearance

18" to 24” is the minimum service panel access depending on model. Refer to the installation manual for details.

24" Unit to Unit Distance

PARTS INFORMATION

Replacement parts are available from local contractor/dealer.

EXTENDED WARRANTY

Special warranty packages (called York Care Performance Promise) are available through your contractor. These packages reduce the potential cost of service calls following the first year of operation on your cooling (or heating/cooling) system.

SOME EFFICIENCY DO’S & DON’TS

DON’T heat or cool unused household area. Reduce supply and return air flow to a minimum in areas which are not living spaces (storage rooms, garages, basements, etc).

DON’T be a “thermostat jiggler”. Moving your thermostat setting will not make your system heat or cool any faster. Adjust your thermostat to a comfortable setting and leave it there.

DON’T restrict air circulation. Placing furniture, rugs, etc. in such a way that they interfere with air vents will make your system work harder to achieve a comfortable temperature level. This requires more energy, which means greater cost to you.

DON’T locate lamps or other heat-producing appliances (radios, TV’s, heaters, etc.) near your thermostat. The heat from these items will give your thermostat “false information” about the temperature in the room.

DO select a comfortable thermostat setting, but keep in mind that mod- eration in temperature selection will save energy.

DO turn on your kitchen exhaust fan when cooking and your bathroom exhaust fan when showering. Also, make sure your clothes dryer is properly vented. If these items are neglected, an excess heat and humidity condition may be created, causing your air conditioning sys- tem to run longer.

DO set your thermostat a few degrees lower than normal several hours before entertaining a large group of people in a relatively small area. People give off a considerable amount of heat and moisture in a closed area.

DO keep drapes and venetian blinds closed when practical. These items provide insulation against heat loss/gain.

DO contact a qualified service person to make repairs or adjustments to your system. He has been trained to perform this service.

Johnson Controls Unitary Products

3

Page 3
Image 3
Johnson Controls SINGLE PHASE Cooling Conservation, Care of System, Coil Care, Service Calls, Filter Care, Clearances

SINGLE PHASE, THREE PHASE specifications

Johnson Controls is a renowned leader in building efficiency and technology solutions, providing innovative products tailored for various power applications, including three-phase and single-phase systems. Understanding the differences between these two types of power systems is essential for optimizing energy management in a range of environments, from industrial settings to commercial buildings.

Three-phase systems are characterized by their use of three alternating currents, each at a equal frequency and amplitude, but staggered by 120 degrees in phase. This configuration delivers a balanced power load, making it highly efficient for large electrical systems. The major features of Johnson Controls' three-phase systems include high energy efficiency, excellent power quality, and reduced harmonic distortion. These systems are ideal for large motors and industrial machinery, as they ensure smoother operation and increased longevity of equipment by providing consistent power.

On the other hand, Johnson Controls' single-phase systems use one alternating current and are typically employed in residential and small business applications. Single-phase power is easier to install and manage, making it a popular choice for everyday electrical needs. Key characteristics of single-phase systems include simplicity and lower setup costs, making it suitable for smaller motors and appliances.

Both three-phase and single-phase systems leverage advanced technologies to enhance performance. For instance, Johnson Controls integrates smart grid technology and IoT solutions into their systems, allowing for real-time monitoring and optimization of energy use. This capability not only improves efficiency but also aids in predictive maintenance, ultimately leading to reduced operational costs and increased reliability.

Moreover, Johnson Controls boasts a commitment to sustainability, incorporating energy-saving technologies that reduce carbon footprints, such as variable frequency drives (VFDs) in their three-phase systems, which optimize motor speed according to demand. Their solutions comply with rigorous standards which ensure safety, quality, and compliance in diverse operational environments.

In summary, Johnson Controls provides sophisticated three-phase and single-phase systems that cater to different energy requirements across a variety of applications. With a focus on efficiency, advanced technology, and sustainability, they stand at the forefront of energy solutions that meet the evolving needs of today's businesses and homes. Through innovation and expertise, Johnson Controls continues to lead the way in creating smarter, more efficient power systems for a sustainable future.