Manuals / Jonsered / Lawn and Garden / Chainsaw

Jonsered CS 2139T manual Bar and chain combinations, Applies to Europe only, Technical Data

Models: CS 2139T

1 36

Download 36 pages 44.5 Kb

Page 35

Bar and chain combinations

TECHNICAL DATA

Bar and chain combinations

The following recommended combinations of bar and saw chain are type approved for your chain saw. The saw chain Jonsered H36 is designed to minimize kickback (classiﬁed saw chain of low kickback type according to ANSI B175.1).

			Bar			Chain

	Length, inch	Pitch, inch	Gauge, mm	Max. nose radius	Type	Length, drive links (no.)

	12	3/8	1,3	7 T	Jonsered H36	45

	14	3/8	1,3	7 T		50
	14	3/8	1,3	7 T		50

Saw chain ﬁling and ﬁle gauges

EC-declaration of conformity

(Applies to Europe only)

Jonsered, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the chain saw Jonsered CS 2139T from 2005’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), is in conformity with the requirements of the COUNCIL’S DIRECTIVES:

-of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.

-of May 3, 1989 ”relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.

-of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

For information relating to noise emissions, see the chapter Technical data. The following standards have been applied: EN ISO 12100-2:2003, CISPR 12:1997, EN ISO 11681-2.

Notiﬁed body: 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has carried out EC type examination in accordance with the machinery directive’s (98/37/EC) article 8, point 2c. The certiﬁcates for EC type examination in accordance with annex VI, have the numbers: 404/05/1061

In addition, SMP, Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has certiﬁed conformity with annex V of the Council’s Directive of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. The certiﬁcates have the numbers: 01/161/056.

The supplied chain saw conforms to the example that underwent EC type examination.

Huskvarna 4 may 2005

Bo Andréasson, Managing Director

English – 35

Image 35

Jonsered CS 2139T Bar and chain combinations, Saw chain ﬁling and ﬁle gauges EC-declaration of conformity, Technical Data

Contents

Operator′s manual Symbols in the operator’s manual KEY TO SYMBOLSSymbols on the machine Contents CONTENTSDear Customer INTRODUCTIONWhat is what on the chain saw? WHAT IS WHAT?Always use common sense GENERAL SAFETY PRECAUTIONSBefore using a new chain saw GENERAL SAFETY PRECAUTIONS Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGENERAL SAFETY PRECAUTIONS Will my hand always activate the chain brake during a kickback?Vibration damping system Stop switchThrottle lockout Chain catcherCutting equipment designed to reduce kickback Cutting equipmentMufﬂer General rulesGENERAL SAFETY PRECAUTIONS Sharpening your chain and adjusting depth gauge settingSome terms that describe the bar and chain General information on sharpening cutting teethSharpening cutting teeth General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainChecking chain lubrication Lubricating cutting equipmentChain oil Filling with chain oilThe clutch drum is ﬁtted with one of the following drive sprockets Chain drive sprocketChecking wear on cutting equipment GENERAL SAFETY PRECAUTIONSFitting a spike bumper ASSEMBLYFitting the bar and chain Two-stroke oil FUEL HANDLINGFuel PetrolLong-term storage Fuel safetyFuelling Transport and storageWarm engine STARTING AND STOPPINGStarting and stopping Cold engineSTARTING AND STOPPING StoppingGeneral working instructions Basic safety rulesWORKING TECHNIQUES Before use6 Always use a fast cutting speed, i.e. full throttle WORKING TECHNIQUESGeneral rules WORKING TECHNIQUES Basic cutting techniqueGeneral TermsSafe distance Felling technique for tree topsCutting LimbingDirectional cuts FellingWORKING TECHNIQUES WARNING! During critical felling operationsWORKING TECHNIQUES General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWORKING TECHNIQUES How to avoid kickbackWhat is kickback? Cutting the trunk into logsFine adjustment MAINTENANCECarburettor adjustment Basic settings and running inChecking the brake trigger Correctly adjusted carburettorChecking brake band wear Checking the front hand guardChain catcher MufﬂerMAINTENANCE Stop switchChanging a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springMAINTENANCE Air ﬁlterSpark plug Lubricating the bar tip sprocketMAINTENANCE Adjustment of the oil pumpCooling system Weekly maintenance Maintenance scheduleMAINTENANCE Daily maintenance´z+Rvh¶6¨ 34 - English´z+Rvh¶6¨ TECHNICAL DATATechnical data TECHNICAL DATA Bar and chain combinationsSaw chain ﬁling and ﬁle gauges EC-declaration of conformity Applies to Europe only1150867-26 ´z+Rvh¶6¨ ´z+Rvh¶6¨