Contents | Jonsered CS 2153 specs

CONTENTS

Contents
KEY TO SYMBOLS
Symbols on the machine:	2
Symbols in the operator’s manual:	2
CONTENTS
Contents	3
INTRODUCTION
Dear customer!	4
WHAT IS WHAT?
What is what on the chain saw?	5
GENERAL SAFETY PRECAUTIONS
Before using a new chain saw	6
Important	6
Always use common sense	6
Personal protective equipment	7
Machine′s safety equipment	7
Cutting equipment	10
ASSEMBLY
Fitting the bar and chain	16
FUEL HANDLING
Fuel	17
Fueling	18
Fuel safety	18
STARTING AND STOPPING
Starting and stopping	19
WORKING TECHNIQUES
Before use:	21
General working instructions	21
How to avoid kickback	28
MAINTENANCE
General	29
Carburetor adjustment	29
Checking, maintaining and servicing chain saw safety
equipment	30
Mufﬂer	32
Starter	32
Air ﬁlter	33
Spark plug	34
Lubricating the bar tip sprocket	34
Needle bearing lubrication	34
Adjustment of the oil pump	34
Cooling system	34
”Air Injection” centrifugal cleaning	35
Winter use	35
Heated handles	35
Maintenance schedule	36
TECHNICAL DATA
Technical data	37
Bar and chain combinations	38
Saw chain ﬁling and ﬁle gauges	38
FEDERAL EMISSION CONTROL WARRANTY
STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS	39
AMERICAN STANDARD SAFETY PRECAUTIONS
Safety precautions for chain saw users	40

English – 3

Image 3

Jonsered CS 2153 manual Contents

Contents

Operator’s manual KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Dear customer Introduction What is what on the chain saw? What is WHAT? General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guard General rules Stop switchCutting equipment Mufﬂer Cutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge setting Instructions considerably increases the risk of kickback General advice on adjusting depth gauge settingIf the depth gauge setting is too large Sharpening cutting teeth Chain oil Adjustment of depth gauge settingTensioning the chain Lubricating cutting equipment Needle bearing lubrication Filling with chain oilChecking chain lubrication Chain drive sprocket Bar Fitting the bar and chain Assembly Fuel Fuel Handling Long-term storage Fuel safetyFueling Transport and storage Warm engine Starting and StoppingStarting and stopping Cold engine Stopping General working instructions Basic safety rulesWorking Techniques Before use General rules Limbing Basic cutting techniqueGeneral Terms Log is supported at one end. There is a high risk that it Tree felling techniqueCutting Safe distance Directional cuts Felling directionClearing the trunk and preparing your retreat Felling Felling cut Cutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped tree How to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral High speed jet H Correctly adjusted carburetor Throttle lockout Mufﬂer StarterChanging a broken or worn starter cord Fitting the starter Air ﬁlterTensioning the recoil spring Changing a broken recoil spring Needle bearing lubrication Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocket Heated handles Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter use Daily maintenance Weekly maintenance Monthly maintenance Maintenance schedule Technical data Technical Data 058/1,5 mm Bar and chain combinationsSaw chain ﬁling and ﬁle gauges 050/1,3 mm Your Warranty Rights and Obligations Federal Emission Control Warranty Statement Other safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage ´z+RI¶55¨ Page 1150419-95 ´z+RI¶55¨ ´z+RI¶55¨