
English
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
INTRODUCTION
5Initial Setup
This section will guide you through the unit’s initial setting which includes selecting a language for your
1After making all the necessary connections, press [POWER] to turn on the unit.
4Use [Cursor s/ B] to select the desired location setting, then press [ENTER].
Initiali l Setup
Select “Retail” or “Home” for your location
RetailHome
Select | NTER Enter |
PREPARATION
• This operation may take a few moments.
2Use [Cursor K/L] to select the
Initialit Setup
|
|
|
|
|
| Select the language for setup display |
| Englsh | |
| Elija el idioma de ajuste |
|
| Español |
| Sélect onner langue écran config |
| Français | |
|
|
|
|
|
| Select | E TER Enter | SETUP | |
|
| Skip | ||
|
|
|
|
|
•“Initial Setup” menu on step 3 will be displayed in the selected language after you press [ENTER].
3Use [Cursor K/L] to select “Antenna” for TV channels or “Cable” for CATV channels, then press [ENTER].
InitialI i i l Setup
Make sure the antenna is connected | o“ANT IN” jack | Antenna | ||
Se ect he dest nation of “ANT IN” jack | ||||
Cable | ||||
|
|
| ||
|
|
| Skip | |
Antenna | Or |
| ||
Cab e | ANT N | |||
|
|
| ||
Select | ENT R Enter | BACK | SETUP | |
Back | Skip |
• “Autoscan” will begin.
Initialit Setup
Now the system s scanning for channels p ease wait
Autoscan w ll take up to 20 m nu es to complete
0%
Analog channels | 0ch |
|
|
|
|
|
|
|
| ||
Digital channels | 0ch |
|
|
|
|
|
|
SETUP
Skip
•Select ”Retail”, the unit will be set up with predefined setting for retail displays. In this setting, the power consumption may possibly exceed the limited requirement of the ENERGY STAR® qualification.
•Select ”Home”, the unit is set to maximize the energy efficiency for home setting and it can be adjusted through a choice of picture and sound quality according to your preference.
•When the initial setup is completed, the lowest memorized channel with the confirmation message of the location setting will be displayed on the TV screen.
Note:
•If you connect the cable system directly, contact the CATV installer.
•If you press [POWER] or [SETUP] during autoscan, this setting will be canceled.
•The initial autoscan function can be executed for either “Antenna” or “Cable” only once. When you change the connection (Antenna / Cable), set autoscan again.
(Refer to page 18.)
•If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the unit, “Helpful Hints” appears. Follow the instructions listed on the TV screen.
InitialIn | Setup |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
No channel s registered |
|
|
| Retry | |
Try Autoscan again? |
|
|
| Later | |
Ver fy that you have a cable connected | o he " ANT IN" jack |
|
|
| |
on he back of the TV the channel nstallation p ocess |
|
|
| ||
searches this connection If you are using a cable or satel ite |
|
|
| ||
box please conf rm the input which you have connec ed the |
|
|
| ||
box and press the “INPUT SELECT” key on the remote con rol to |
|
|
| ||
se ect he appropr ate source input |
|
|
|
| |
|
|
|
|
| |
| Select | EN ER Enter | SETUP | ||
|
| Skip | |||
|
|
|
|
|
|
•You must set ”Home” in step 4. Otherwise, the settings of picture and sound quality you adjusted will not be memorized after you turn off the unit.
After an initial setup is completed...•If you want to scan the channels automatically again, refer to “Autoscan” on page 18.
•You can add the desired channels unmemorized by “Autoscan”. Refer to “Manual Register” on page 19.
•If you want to change to another language, refer to “Language Selection” on page 20.
•If you want to change the location setting, refer to “Location” on page 31.
INFORMATION TROUBLESHOOTING SETTING OPTIONAL TV WATCHING
13
EN