Rear Side/ Right Side/ Bottom Surface | JVC DLA-SX21U specs

Controls and Features

Rear Side/ Right Side/ Bottom Surface

q Connector Panel

w Speaker

7Air Inlet

e Lamp Cover

tRemote Sensor (Rear)

r Exhaust Vents

Bottom Surface

y Front Adjustable

Foot

7 Air Inlet

u Filter

i Rear Fixed

Foot

Blocked as it is not in use. Opening it forcibly will cause damage to the machine.

qConnector Panel

For details, refer to ‘Connector Panel’ . (☞ page 9)

wSpeaker

Built-in speaker located here.

eLamp Cover

Remove this cover when replacing the lamp. (☞ page 43)

rExhaust Vents

Warm air is expelled through these vents to keep the sys- tem cool. Please do not block the exhaust vents.

tRemote Sensor (Rear)

When operating with the remote control, aim it towards this sensor. (☞ page 18)

*A remote sensor is also provided at the front of the projec- tor.

yFront Adjustable Foot (for adjusting the height and angle)

It is set at the lowest position when shipped from the fac- tory. The foot can be adjusted to a maximum angle of +6° and a maximum length of 31mm. (☞ page 15)

uFilter

Cleans air drawn in from the air inlet. Please clean the filter regularly with eg, a vacuum cleaner. (☞ page 46)

iRear Fixed Foot

8

Image 8

JVC DLA-SX21U manual Rear Side/ Right Side/ Bottom Surface, Controls and Features

Contents

DLA-SX21U/DLA-SX21E Instructions DLA-SX21SU/DLA-SX21SE For customer Use FCC Information U.S.A. only Machine Noise Information Germany only Power cord Safety PrecautionDo not allow any unqualified person to install the unit Wire which is coloured green-and-yellow must be con How To Replace The FuseBrown Live Do not cut off the main plug from this equipment Using the screen mode switch function About burning-in of the D-ILA deviceViewing conditions Care Contents Accessories Controls and Features Front Side/ Top Surface/ Left Side Controls and Features Rear Side/ Right Side/ Bottom Surface Connector Panel Indicator Display on the Control Panel Control Panel on the ProjectorStand by light on Operate light on Stand by blinking Alternately*2 Stand by Indicator Operate IndicatorLamp Indicator Volume ª / · buttons Remote Control’s signal transmitter Remote Control UnitVolume button Remote Control’s signal transmitter Operate button Volume ª / · buttonScreen button Digital Zoom ª / · buttons Loading Batteries into the Remote Control Precautions for using batteriesOpen the back cover Load the batteries Installing the Projector Precautions for Installation Installing the Projector against the Screen Installing the ProjectorPrecaution for ceiling-mount Mounting the Projector Screen installation Projection Distance and Screen Size169 Screen For DLA-SX21U/DLA-SX21E Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit Using as a wired Remote Control When the remote control unit fails to work properly Connecting to Various Devices Signals that can be input into the projector Video signals Computer signals Connecting to Various Devices Allowable input signalsSignal HorPixels Ver Lines KHz Connecting to Devices Connecting to Video Devices Connecting to Computers Desktop type DOS/V, etc Desktop type DOS/V, PC-9800 etcDesktop type Right side of projector Control from external device Connection for controlling more than one projectorCross cable RS-232C connection cable separately available Cross cable Connecting the Power Cord supplied When using the projectorPower cord supplied Removing the Lens Cap Basic Operation Procedures Power OnBasic Operations Selecting the image to be projected Display using the direct buttons Adjusting the Focus Ring Focus for DLA-SX21U/DLA- SX21EBasic Operations Screen display Power Off Adjusting the Sound Volume Enlarging the Image Digital zoom DisplayFrequently used Convenient Functions Turning Off Image and Sound Displaying a Still PicturePress the Hide button once Press the Freeze button Press V-KEYSTONE / to adjust in the vertical direction Press H-KEYSTONE / to adjust in the horizontal directionRemoving the Trapezoidal Distortion of the Image Vert. Keystone Display Using the Quick Alignment function Selecting the Screen Size Screen size display Press the Quick ALIGN. Quick Alignment button Adjustments and Settings Using Menus Menu StructureMain menu Submenu Main Information menu Main Image adj. menuOnly in English Adjustments and Settings Using Menus Main Set up menu Displayed only when PC is selectedSubmenu Main Logo menu Capture menu Capture start Menu Operation Buttons Procedure for Menu Operation Menu Configuration Set up menuImage adj. menu Color temp. menu Logo menu Position menuDecoder menu Capture menu Capture start Options menu qColor profile menu Language menu When no image signal is inputted Information menu Editing and Projecting Logo Project the images to be included in your logoSelect Logo with the Cursor buttons / Press the Enter or the right Cursor button Editing and projecting logo Procedure for lamp replacement About lamp replacementReplacing the Lamp Light source lamp and its lamp time Replacing the Lamp Remove the lamp unitInsert the new lamp unit until it is fully Close the handle, and tighten the screw Resetting the lamp time Cleaning and Replacing the Filter Pull out the power cord from the wall outletClean the filter Reinstalling the filter Troubleshooting Symptom Probable cause Corrective action Troubleshooting What to do when these messages are displayed Message Cause Contents What to do when these messages are displayed Press any key to delete the message About warning indicators Please follow the procedures belowIndicator Action to be taken upon warning indications Specifications Preservation temperature 14F ~ 140F -10C ~ +60CLine, DVI-D single-24pin terminal Excluding handle, foot, lens and protrusion portion Mass Specifications Dimensions unit mm Pin number Signal name Pin arrangement Y/C terminal RS-232C IN/OUT terminal PC 1 terminal RS-232C external control External control command table Operation mode parameters Character Hex MeaningOperation mode Only Asking command is possible Function Memo SW-VP