Troubleshooting
|
| PROBLEMS |
|
| CHECK | |
|
| There is no power | • See if the power cord became unplugged. |
|
| |
|
|
| • Check for a blown fuse or circuit breaker or a power outage. | |||
|
|
| • | It is possible the fan is stuck or the inside temperature is rising abnormally. | ||
|
|
|
| Consult your dealer. |
|
|
|
|
|
|
|
| |
|
| The POWER LED | • | It may be a malfunction that the fan is locked or the temperature has increased. | ||
|
| and LAMP/PROGRAM |
|
|
|
|
|
| LED are blinking |
|
|
|
|
|
| alternately. |
|
|
|
|
|
|
|
|
| ||
|
| The POWER LED | • The lamp may not have been installed correctly, or it may be due to a malfunction. | |||
|
| and LAMP/PROGRAM | • The lamp door may not be closed correctly. | |||
|
| LED are blinking |
|
|
|
|
|
| rapidly simultaneously. |
|
|
|
|
|
|
|
|
|
| |
|
| There is no picture | • The antenna could be disconnected. |
|
| |
|
| or sound | • The input mode could be set improperly. See page 68. | |||
|
|
| • The tuner (Auto Tuner Setup) could be set improperly. See page 37. | |||
|
|
| • The TV station may be having difficulties. Check to see if other stations are working. | |||
|
|
| • Use the HDMI cable with HDMI logo |
| . See page 22. | |
|
|
|
| |||
|
|
| • You can not output audio using the AUDIO OUTPUT under the following conditions: | |||
|
|
|
| 1) When you have digital sound from an HDMI device connected to the HDMI 1 or | ||
|
|
|
| HDMI 2 connection on the back of your TV. (See page 22). | ||
|
|
|
| 2) When you have analog sound from a DVI device connected to the | ||
|
|
|
| AUDIO IN "HDMI 1" connection. (See page 21). | ||
|
|
| • When you have an HDMI device connected to the HDMI 1 connection on the back of your | |||
|
|
|
| TV, your TV detects it, and blocks the analog audio signal coming into the "HDMI 1” | ||
|
|
|
| jacks. Therefore, you can not hear any analog sound from the other device conected to the | ||
|
|
|
| "HDMI 1" jacks, while you are viewing the images from the HDMI device. | ||
|
|
|
| (See page 22). |
|
|
|
|
|
|
| ||
|
| Remote control is not | • Check to see that the batteries are still working and properly installed. | |||
|
| operating properly or | • Make sure the remote has a clear sight path to the TV. | |||
|
| at all | • Check that the TV/CATV switch is in the proper position. | |||
|
|
| • You may be too far from the TV. You must be within 23 feet (7 meters). | |||
|
|
|
|
| ||
|
| You cannot select a | • Make sure the channels have been programmed. See "Channel Summary", page 38. | |||
|
| certain channel | • Check to see if the channel is locked. See "Channel Summary - Lock" page 39. | |||
|
|
|
|
| ||
|
| The power turns off | • Make sure the set did not become unplugged. | |||
|
| by itself | • Perhaps the On/Off Timer is set. See page 64. | |||
|
|
| • Check to see if the Sleep Timer was set. See page 72. | |||
|
|
|
|
| ||
|
| It does not operate | • This television is operated by a microprocessor. It is possible that external noise or | |||
|
| correctly |
| interference is causing the problem. If the television does not function correctly, remove the | ||
|
|
|
| electrical plug from the wall outlet and wait a while before inserting it into the wall outlet | ||
|
|
|
| again and operating the television. |
|
|
|
|
|
|
| ||
|
| The clock is wrong | • The power was interrupted and the clock was not reset. See page 63. | |||
|
|
|
|
| ||
|
| The color quality | • Tint and Color may be improperly adjusted. See page 59. | |||
|
| is poor | • The Video Status mode may be turned to the wrong setting. See page 71. | |||
|
|
|
|
| ||
|
| There are lines | • There could be interference from another electrical appliance, such as a computer, | |||
|
| across the picture |
| another TV or VCR. Move any such appliances further away from the TV. | ||
|
|
|
|
| ||
|
| The picture is spotted | • There could be interference from a | |||
|
|
|
| operating nearby. Move the antenna away from the appliance or change to a coaxial | ||
|
|
|
| cable connection which is less prone to interference. | ||
|
|
|
|
| ||
|
| There are double | • A building or passing airplane can reflect the original signal and produce a second, | |||
|
| pictures (ghosts) |
| slightly delayed one. Adjust your antenna position. | ||
|
|
|
|
| ||
|
| Picture is snowy | • Your antenna may be damaged, disconnected or turned. Check the antenna | |||
|
| (image noise) |
| connection. If the antenna is damaged, replace it. | ||
|
|
|
|
| ||
|
| Screen is 80% black | • The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 73. | |||
|
|
|
|
|
|
|
|
| Stereo or bilingual | • Make sure the MTS settings are correct. See page 72. | |||
|
|
| ||||
|
| programs can't be |
|
|
|
|
|
| heard |
|
|
|
|
|
|
|
|
| ||
|
| The LAMP/PROGRAM | • It may be a malfunction of the internal electrical circuits. | |||
90 |
| LED continues blinking |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|