Parts list for installation and connection

A/ B

C

D

E

F

Hard case/Control panelSleeveTrim platePower cord

Washer (ø5)

G

H

I

J

K

L

Lock nut (M5)Mounting bolt—Rubber cushionHandlesRemote controller

Battery

 

M5 x 20 mm (M5 x 13/16")

 

 

 

 

INSTALLATION

The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

In dash-mounting

 

Removing the unit

 

 

 

INSTALLATION / CONNECTION
Do the required electrical connections.
Before removing the unit, release the rear section.

When you stand the unit, be careful not to damage the fuse on the rear.

Bend the appropriate tabs to hold the sleeve firmly in place.

When using the optional stay

Fire wall

Stay (option)

DashboardScrew (option)Install the unit at an angle of less than 30˚.

When installing the unit without using the sleeve

In a Toyota car for example, first remove the car radio and install the unit in its place.

 

Flat type screws—M5 ⋅ 8 mm (M5 ⋅ 3/8")*

* Not supplied for this unit.

Bracket*

 

Flat type screws

 

—M5 ⋅ 8 mm (M5 ⋅ 3/8")*

 

Pocket

 

Bracket*

 

ELECTRICAL CONNECTIONS

Typical connections

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.

1Connect the colored leads of the power cord in the order specified in the illustration below.

2Connect the antenna cord.3Finally connect the wiring harness to the unit.
Rear ground terminal

Line out

Connecting the external amplifier or subwoofer

 

Remote leadY-connector *1

 

Remote lead (blue with white stripe)

 

Set “L/O MODE” to “REAR”

 

 

 

(See “General settings—PSM.”)

To the remote lead of other equipment

You can connect a power amplifier for
or automatic antenna if any
rear speakers.

 

 

 

Antenna terminal

Connect only the front speakers if your speaker system is two-speaker system.

White with black stripe
Front speaker (left)

White

Gray with black stripe

Front speaker (right)

Gray

15 A fuse
Black

To metallic body or

 

chassis of the car

To a live terminal in the

Yellow *2 fuse block connecting to the car battery (bypassing the

ignition switch) (constant 12 V)
Red

To an accessory terminal in

 

the fuse block
Ignition switchFuse block
JVC Amplifier

 

 

Rear

 

 

speakers

 

 

 

 

Front speakers

Set “L/O MODE” to “WOOFER”

 

 

(See “General settings—PSM.”)

 

 

You can also connect a subwoofer to

*1

Not supplied for this unit.
the REAR LINE OUT terminals.

 

*2

Before checking the operation of this unit prior to installation, this

 

 

lead must be connected, otherwise power cannot be turned on.

 

*3

Firmly attach the ground wire to the metallic body or to the chassis

JVC Amplifier

or

of the car—to the place uncoated with paint (if coated with paint,

 

 

remove the paint before attaching the wire). Failure to do so may

Subwoofer

 

 

cause damage to the unit.

 

 

 

*4

Signal cord (not supplied for this unit)
PRECAUTIONS on power supply and speaker connections:
Green with black stripe
Rear speaker (left)

Green

Purple with black stripe
Blue with whitestripeTo the remote lead of other equipment or automatic antenna if any (200 mA max.)

•DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

•BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

Rear speaker (right)

Purple

4 – EN