Parts list for installation and connection
A | B | C | D |
| Control panel | Sleeve | Trim plate | Power cord |
E | F | G | H | I | J | K | |
| Washer (ø5) | |||||||
| Lock nut (M5) | Mounting bolt— | Rubber cushion | Handles | Remote controller | Battery | ||
| |||||||
|
| M5 x 20 mm (M5 x 13/16") |
|
|
|
|
INSTALLATION
If you are not sure how to install this unit correctly, consult your JVC car audio dealer.
In |
| Removing the unit |
|
|
|
When you stand the unit, be careful not to damage the fuse on the rear.
When using the optional stay
| Fire wall | Stay (option) |
When installing the unit without using the sleeve
In a Toyota car for example, first remove the car radio and install the unit in its place. |
|
| Flat type | * Not supplied for this unit. |
| Bracket* |
|
| Flat type screws |
|
| |
| |
Bracket* |
|
ELECTRICAL CONNECTIONS
Make sure to disconnect the battery’s negative terminal.• Be sure to ground this unit to the car’s chassis again after installation.HighNote:
It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the
Heat sinkmaximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page “General setting — PSM“ of the INSTRUCTIONS.).
|
| Typical connections |
|
| Connecting the external amplifier or subwoofer (for | |||||
| Rear ground terminal | Line out (for |
|
|
|
|
|
| Remote lead | ||
|
|
|
|
|
| Set “L/O MODE” to “REAR” |
|
| Remote lead (blue with white stripe) | |
|
| 15 A fuse |
|
|
|
|
|
|
| |
|
|
|
|
| (See “General |
|
|
|
| |
|
|
|
|
|
|
|
|
| To the remote lead of other equipment | |
| Antenna terminal |
|
|
|
| You can connect a power amplifier for |
|
|
| ||
|
|
|
|
|
|
| or automatic antenna if any | |||
|
|
|
|
|
| rear speakers. |
|
|
| |
|
|
|
| Ignition switch |
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
Connect only the front speakers if your | Black | To metallic body or |
|
|
|
|
|
|
| |
| chassis of the car |
|
| JVC Amplifier |
|
|
|
| ||
speaker system is |
|
|
|
| Rear |
|
|
|
| |
|
|
| To a live terminal in the |
|
|
|
|
|
| |
| White with black stripe |
|
|
| speakers |
|
|
|
| ||
| Yellow *2 | fuse block connecting to the |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| Front speakers | ||
|
|
| car battery (bypassing the |
|
| Set “L/O MODE” to “WOOFER” |
|
|
| |
|
|
|
|
|
|
|
|
| ||
| Front speaker (left) | White |
| ignition switch) (constant |
|
|
|
|
|
| |
|
|
| (See “General |
|
|
|
| |||
| 12 V) |
|
|
| *1 | Not supplied for this unit. |
| |||
|
|
| Fuse block |
| You can also connect a subwoofer to |
|
| |||
| Gray with black stripe |
|
|
|
| *2 | Before checking the operation of this unit prior to installation, this | ||||
|
|
|
| the REAR LINE OUT terminals. |
| |||||
| Red | To an accessory terminal in |
|
|
|
| lead must be connected, otherwise power cannot be turned on. | ||||
|
|
|
|
|
| *3 | ||||
| Front speaker (right) | Gray |
| the fuse block |
|
|
| or | Firmly attach the ground wire to the metallic body or to the chassis | ||
|
|
|
| JVC Amplifier |
| of the | ||||
|
|
|
|
|
| |||||
|
| Blue with white |
|
| Subwoofer |
|
| remove the paint before attaching the wire). Failure to do so may | ||
| Green with black stripe |
|
|
|
| cause damage to the unit. |
| ||||
|
|
|
|
|
| |||||
|
| stripe | To the remote lead of other |
|
|
| *4 | Signal cord (not supplied for this unit) | ||
|
| equipment or automatic antenna if |
|
|
| |||||
|
|
|
|
|
|
|
|
| ||
| Rear speaker (left) | Green |
| any (200 mA max.) |
|
| PRECAUTIONS on power supply and speaker connections |
| |||
|
|
|
|
| ||||||
| Purple with black stripe |
|
|
|
|
|
|
|
|
| |
| Rear speaker (right) | Purple |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 – EN |
|
|
|
| |