KS-AX3002 (for USA)
2-speaker system plus subwoofer (1 amplifier)
The minimum impedance should be 4 Ω for each of left and right speakers, and the subwoofer.
JVC car receiver, etc.
Filter switch
Line out
*2
| b Speaker input connector |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| Connector lead |
| To |
| Receiver |
| * | 3 |
|
|
| * | 4 |
| * | 3 |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
| Å White "LEFT (+)" |
| = |
| Left (+) lead |
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
| ı Black "RECEIVER GND" |
| = |
| Chassis*1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
| Ç Gray "RIGHT (+)" |
| = |
| Right (+) lead |
|
|
|
| Subwoofer | |||||||||||
|
|
|
|
|
|
| Right speaker |
|
| Left speaker | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*1 | See page 2. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
*2 | RCA pin cords (not provided) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
*3 | Use a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
*4 | Use a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
CONTROLS
KS-AX3004
ÅPOWER indicator
The green lamp lights while the unit is turned on.
ıCROSSOVER filter switch
OFF: Normally set to this position. The switch is preset to this position when the unit is shipped.
LPF: Set to this position when you want to turn on the LPF
HPF: Set to this position when you want to turn on the HPF
ÇInput LEVEL controller
The input level can be adjusted with this control when this unit is connected to other source equipment. Adjust the level while listening to the sound. This control is preset to MIN when the unit is shipped.
TROUBLESHOOTING
For more details, consult your “JVC
The POWER indicator does not light.
•Change the fuses if the current one is blown.
•Connect the ground lead securely to a metal part of the car.
•Turn on the equipment connected to this unit.
•Confirm the battery voltage (11 V to 16 V).
•Use a relay if your system employs too many amplifiers.
•Leave the unit turned off to cool it down if it heats up abnormally.
No sound is heard.
•Confirm the connections for the power supply (see "POWER SUPPLY" on page 1).
•Connect the RCA pin cords to the INPUT jacks, or the speaker input connector to the HIGH INPUT terminal.
•Confirm the speaker wirings and the position of the CROSSOVER filter switch (See “SPEAKER CONNECTIONS” on page 2).
Alternator noise is heard.
•Keep the leads of the POWER terminals away from the RCA pin cords.
•Keep the RCA pin cords away from other electrical cables in the car.
•Connect the ground lead securely to a metal part of the car.
•Make sure the speaker negative leads do not touch the car chassis.
•Connect a bypass capacitor across the accessory switches (horn, fan, etc.).
Noise is made when you connect the unit to an AM (MW/LW) tuner.
• Move all the leads of this unit away from the antenna (aerial) lead.
SPECIFICATIONS
Power Output | 60 W RMS x 4 channels at 4 Ω and ≤ 1% THD + N | |
| • Normal Mode: | |
|
| 65 W RMS x 2 channels at 4 Ω and ≤ 1% THD + N |
| • Normal Mode: | |
76 dBA (reference: 1 W into 4 Ω) | ||
Power Output | 85 W RMS x 4 channels at 2 Ω and ≤ 1% THD + N | |
| • Normal Mode: | |
| • Bridge Mode: | 120 W RMS x 2 channels at 4 Ω and ≤ 1% THD + N |
| 90 W RMS x 2 channels at 2 Ω and ≤ 1% THD + N | |
| • Normal Mode: | |
| • Bridge Mode: | 130 W RMS x 1 channel at 4 Ω and ≤ 1% THD + N |
Maximum Power Output | ||
|
| |
Load Impedance | • Normal Mode: | 4 Ω (2 Ω to 8 Ω allowance) |
| • Bridge Mode: | 4 Ω (4 Ω to 8 Ω allowance) |
Frequency Response | 5 Hz to 50,000 Hz (+0 dB, | |
Input Sensitivity/Impedance | 2 V/12 kΩ (0.3 V to 6 V, variable) | |
Distortion | Less than 0.04% (at 1 kHz) | |
Power Requirement | DC 14.4 V (11 V to 16 V allowance) | |
Grounding system | Negative ground |
|
Dimensions (W×H×D) | ||
| ||
Mass (approx.) | ||
| ||
Accessories | Speaker input connector 6P × 1 | |
| Mounting Screw φ 4 × 20 mm (13/16 in.) × 4 | |
Design and specifi cations are subject to change without notice.
Information for Users on Disposal of Old Equipment
This symbol indicates that the product with this symbol should not be disposed as general household waste at its
This symbol is only valid in the European Union.
Dear Customer,
This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan, Limited is: JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg Germany
3
