Before Switching OnYour TV

Power Connection

IMPORTANT: The TV set is designed to operate on 220 - 240 V AC, 50 Hz.

• After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains.

Connections To The RF Input

 

 

 

Socket

NOTE: Remove batteries from remote con-

• Connect the aerial or cable TV plug to the RF

trol handset when it is not to be used for a long

period.Otherwise it can be damaged due to

input socket located at the back of the TV

any leakage of batteries.

 

 

and connect the cable plug coming out from

 

 

 

 

 

the TV out socket located at the devices (VCR,

Switching The TV ON/OFF

DVB etc.) to this socket as well.

 

 

 

To switch the TV on:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Your TV will switch on in two steps:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1- Connect the power supply cord to the sys-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

tem. Press On/Off switch at the rear of the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TV. Then the TV switches itself to stand-by

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mode and the power lamp becomes red lo-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cated on the front of the TV.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2- To switch on the TV from stand-by mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

either:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press a digit button on the remote control so

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

that a programme number is selected,

How To Connect Other Devices

or,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMPORTANT: Switch off the TV before connect-

Press “ / I”, "-P/CH" or "P/CH+" button at the

ing any external device.

top of the TV or press “

” or “

” button

Sockets for external connections are at the

on the remote control, so that last switched off

back and side of the TV. For connection of other

programme is selected.

 

 

devices via Euroconnector refer to the manu-

By either ways the TV will switch on and the

als of the related devices.

power lamp becomes green.

 

Inserting Batteries In The Remote

 

To switch the TV off:

 

 

Control Handset

 

 

• Press the “stand-by” button on the remote

• Place the batteries in the right directions as

control, so the TV will switch to stand-by

seen below.

mode and the power lamp will become RED,

• Remove the battery cover located on the back

or,

 

 

of the handset by gently pulling upwards from

Press the “ / I” button located on the top of

the indicated part.

• Insert two AA/R6 dry cell or equivalent type

the TV, so the TV will switch off and the power

lamp will become RED.

 

 

of batteries inside.

 

 

To switch the TV off completely press On/Off

• Replace the battery cover.

switch at the rear of the TV and remove the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mains plug from the socket.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENGLISH - 9 -