Accessories

A Hexagonal head tapping screw

B Hexagonal head tapping screw

C Protection bar x 4

x 16 (R4 x 30 mm)

x 8 (R4 x 20 mm)

 

CAR STEREO SPEAKER

CS-WDS1

Use a M4 hex wrench.

DPaper pattern

How to use the paper pattern

1.Cut out the paper pattern along the perforation.

2.Place and trace the paper pattern over the mounting area on the vehicle or board.

3.Cut out the mounting area on the vehicle or board along the marking.

For Tweeter

For Woofer

Specifications

The diaphragm of this speaker makes use of birch wood to faithfully reproduce the original sound. Each unit, therefore, has a unique appearance.

Type

: 2-Way Separate Speaker

Frequency Response

: 45 Hz - 50 kHz

Sound Pressure Level : 84 dB/W 0m

Recommended Crossover Frequency

: 4.5 kHz (Cut-off Slope:-12 dB/oct.)

14.5cm Wood Cone Woofer

Power Handling Capacity (Nominal)

 

: 50 W

Power Handling Capacity (Max. Music Power)

 

: 150 W

Impedance

: 4 K

Frequency Response

: 45 Hz - 8 kHz

Sound Pressure Level : 84 dB/W 0m

Mass

: 1.5 kg (one piece)

2cm Wood Dome Tweeter

Power Handling Capacity (Nominal)

:50 W (4.5 KHz -12 db/oct. H.P.F.)

Power Handling Capacity (Max. Music Power)

:150 W (4.5 KHz -12 db/oct. H.P.F.)

Impedance

: 4 K

Frequency Response

: 3 kHz - 50 kHz

Sound Pressure Level : 84 dB/W 0m

Mass

: 235 g (one piece)

Thiele/ Small Parameter (14.5 cm Woofer)

Revc (DC VC Res )

3.4

Ohms

 

 

 

Imp. (300Hz)

4

Ohms

 

 

 

Fo (Res Freq )

80.2

Hz

 

 

 

Zo (Zmax at Fo)

26.9

Ohm

 

 

 

Sd (Piston Area)

0.0095

sqM

 

 

 

BL (Flux*Length)

6.08

TM

 

 

 

Qms (Mech Q)

3.814

 

 

 

 

Qes (Elec Q)

0.667

 

 

 

 

Qts (Total Q)

0.568

 

 

 

 

Vas (Acous Vol)

4.13

Litr

 

 

 

Le (Inductance)

0.286

mH

 

 

 

Cms (Compliance)

321.9

uM/N

 

 

 

Mms (Total Mass)

12.23

Gram

 

 

 

Mmd (DiaphmMass)

11.70

Gram

 

 

 

Thank you for purchasing the JVC Car Stereo Speakers. For the secure installation and perfect operation of your speaker, please read the following instructions carefully.

Mounting the speaker

Professional knowledge is required for mounting this speaker. For details, please consult the authorized dealer. Make use of the paper pattern provided when processing the mounting board of the speaker.

During mounting, ensure that there is enough spacing to avoid hitting against any parts such as window glass.

In order to optimize the sound field of the wood cone, it is recommended that the speaker terminal be mounted at the bottom with the wood grain in the vertical direction.

Notes for dealers

Upon completing the mounting, please hand this instruction manual to the customer.

For Proper Installation and Use

1.

Be sure to install the speakers according to the directions so as to prevent them from slipping accidentally out of position due to the

 

repeated impact of opening and closing doors or the tossing and bumping of the vehicle.

2.

Set the wiring firmly on the floor of the vehicle, taking the utmost care not to break wires while installing. When installing the speakers

 

in the doors, extra attention must be paid to allowing reasonable play to the wires. The wiring, if given too much clip or clamp, will get

 

pinched in between the door and body of the vehicle when opening and closing doors.

3.

Since the speaker installed in the door is positioned at the foot level, be careful not to damage the speaker by giving it an inadvertent

 

kick. Check the water outlet at the bottom of the door occasionally to ensure that it drains well, leaving no rainwater inside the door.

4.

Before connecting the speakers to the amplifier, confirm that the power has been turned off. The click noise generated by the

Designs and specifications are subject to change without notice.

 

connection if the power is on may damage the speakers.

5.

The amplifier and speakers should be connected between corresponding terminals, i.e. “left” to “left”, and “right” to “right”, as well as

 

“+” to “+”, and “–” to “–”. Connection with reversed polarity will degrade the quality of stereo reproduction.

6.

Do not subject the speakers to excessive input. Any excessive input may damage the speakers.

7.

Make sure that the output impedance of the amplifier’s speaker terminal is rated at 4 ohms.

8.

Please use a high-pass filter.

 

(Cut-off Frequency is 4.5 kHz and above -12dB/oct)

9.

When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not apply thinner or solvent.

INSTRUCTIONS

EN

 

LVT1405-002A

 

[E]

2006 Victor Company of Japan, Limited

0606SKMSANTCN

Page 1
Image 1
JVC LVT1405-002A specifications Accessories, Specifications, Mounting the speaker, For Proper Installation and Use