Using the CD Player

Programming the Playing Order of the Tracks

You can program the playing order of the tracks on all the CDs. Note that you can only make a program when the CD Player is stopped.

❏You can program up to 32 tracks in any desired order including the same tracks.

For MP3 discs

•If you try to select a MP3 disc that has once been read or played, “MP3 DISC” appears on the display and it can not be programmed.

•MP3 disc that has not ever been read can be selected in a program mode. But when playback starts, “MP3 DISC” appears on the display, the program is deleted and switched to a next program.

To Make a Program

1 Load CDs.

2 In Stop mode, set the CD Player in Program Play mode.On the Unit

Press the PROGRAM button to light the “PRGM” indicator on the display.

At the same time, “PROGRAM” appears on the display.

On the Remote Control

Press the PROGRAM/RANDOM button until “PROGRAM” appears on the display.

The “PRGM” indicator also lights up on the display.

Each time you press the button, the display changes as follows: PROGRAM = RANDOM = Normal display (Normal Play) = (back to the beginning)

•If a program is already made, the last step of the program will be displayed.

3 Press one of the Disc button (CD1-CD3) to select the CD you want to program.

The display will change to the Program Entry display.

CD1

or

Disc number Track number

4 Select the track you want to program.Using the Unit

While the display is blinking, press the 4 or ¢ button on the Unit to select the track, then press the SET button within 5 seconds. The program order number will be assigned from P-1.

Disc number Track number

Program order number

Using the Remote Control

Press the numeric keys to directly enter the track number. Then, the program order number will be assigned from P-1.

•To delete the current program step, press the CANCEL button on the Unit.

5 Repeat steps 3 and 4 to program other tracks on the same CD or the other CD.6 To play the program, Press the CD 6 but- ton.

For details, see “To Play the Program You Have Made” mentioned below.

To confirm the programmed contents, while the CD player is stopped, select Program mode by pressing the PROGRAM button and press the 4or ¢button on the Remote Control.

To delete all the tracks in the program, while the CD Player is stopped, press the 7button or open the tray by pressing the CD Open/Close 0button.

To Modify the Program, while the CD Player is stopped and the program mode is selected, press the CANCEL button, the last track in the program is deleted. To add new tracks to the end of the pro- gram, repeat above steps 3 and 4.

•If you try to program a track number that does not exists on the CD, your entry will be ignored.

•If you try to program the 33rd track, “FULL” appears on the display.

To Play the Program You Have Made

Press the CD 6button.

The System plays the tracks in the order you have programmed them.

•To use Repeat Play for Program Play, press the REPEAT but- ton to select “REPEAT” before starting playback. For details, see “Repeating Tracks” on page 15.

❏You can skip to a particular program track by pressing the 4 or ¢button during Program Play.

❏To stop playing, press the 7button once. If you press the 7but- ton, while the CD Player is stopped, the program is deleted.

To Exit and Re-enter Program Play

The program you have made is stored in memory. So, you can exit Program Play temporarily or re-enter Program Play unless you delete the program.

To exit the program mode once, press the 7 button to stop playing. The “PROG” indicator goes off and the Program mode will be canceled. The program is stored in the memory.

To re-enter Program Play mode, press the PROGRAM or PROGRAM/RANDOM button until the “PRGM” indicator lights up again.

•When the power is turned off (standby mode), the pro- grammed tracks are deleted.

•Tray will not open during the program playback.

14