ENGLISH
CD PORTABLE SYSTEM
GETTING STARTED
POWERING UP
This CD portable system operates on battery or AC power.
BATTERY POWER
Insert six batteries R20
Important Battery Information
•If you are not going to use your system for a month or more, be sure to remove batteries because they can leak and cause damage.
•Dispose of batteries in the proper manner, according to federal, state, and local regulations.
•Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury.
FM telescopic antenna
BEAT CUT/FM MODE switch
Battery compartment | AC IN jack |
PHONES jack
RECORDING FROM THE RADIO
1.Insert a cassette tape into the tape deck and close the door.
2.Move FUNCTION to TUNER and select a radio station.
3.Press REC 
to begin recording. REC 
and PLAY 
lock down.
4.Press STOP/EJECT 
to end recording.
5.To turn off the radio, slide FUNCTION to 
OFF/TAPE.
RADIO RECORDING TIPS
•To temporarily pause the recording, press PAUSE 
on the cassette deck. Press PAUSE 
again to resume recording.
SYNCHRONIZED RECORDING FROM A CD
1.Insert a cassette tape into the tape deck and close the door.
2.Move FUNCTION to CD.
3.Insert the CD you want to record into CD compartment.
4.Select the track you want to record by pressing 
(skip/search) or 
(skip/search).
5.Press REC 
to start recording.
Note that the tape continues to run when the CD finishes playing, or the CD continues to play when the tape reaches the end.
TIP
CARE AND MAINTENANCE
CLEANING THE EXTERIOR
• Disconnect the system from AC power before cleaning the exterior of the unit with a soft dust cloth.
HANDLING CDS
•Do not touch the signal surfaces. Hold by the edges, or by one edge and the hole.
•Do not affix labels or adhesive tape to the label surfaces. Also, do not scratch or damage the label.
•Discs rotate at high speed inside the player. Do not use damaged (cracked or warped) discs.
CLEANING CDS
•Dirty discs can cause poor sound quality. Always keep discs clean by wiping them gently with a soft cloth from the inner edge toward the outer perimeter.
•If a disc becomes dirty, wet a soft cloth in water, wring it out well, wipe the dirt away gently, and then remove any water drops with a dry cloth.
•Do not use record cleaning sprays or antistatic agents on discs. Also, never clean discs with benzene, thin- ner, or other volatile solvents which may cause damage to the disc surface.
TAPE CARE
• Do not expose tapes to sunlight or store in hot places. High temperatures may warp the shell or damage the |
INSTRUCTIONS
Thank you for purchasing this JVC product.
Please read these instructions carefully before starting operation to be sure to obtain optimum performance and a longer service life from the unit.
LVT1374-007A [EN]
0205NSMBICORI
EN ©2005 Victor Company of Japan, Limited
SAFETY PRECAUTIONS
Caution 
OFF switch!
Disconnect the mains plug to shut the power off completely. The switch in any position does not disconnect the mains line. The power cannot be remote controlled.
CAUTION
AC POWER
Plug the power supply cord into the Ó AC IN jack on the back of the unit, and into an AC power outlet.
CAUTIONS:
1.ONLY USE JVC POWER CORD PROVIDED WITH THIS UNIT TO AVOID MALFUNCTION OR DAMAGE TO THE UNIT. REMOVE BATTERIES WHEN USING THE POWER CORD.
2.BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN THE UNIT IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.
USING HEADPHONES
Connect commercially available headphones to the PHONES jack on the rear of the main unit. While the head- phones are connected, the speakers do not produce any sound. Before connecting the headphones, make sure to turn down the sound volume.
ANTENNAS
The AM antenna is built in, so adjusting the position of the unit may help AM reception. The FM telescopic antenna on the back of the unit can be extended and rotated for better FM reception.
GENERAL CONTROLS
FUNCTION switch – Move the switch to select which part of this system you want to select – TUNER, TAPE or CD.
VOLUME – Turn the volume knob to increase or decrease the volume to desired level.
HBS – Press so that the HBS indicator lights. You can enjoy powerful bass sound with the
POWER OFF – Move FUNCTION to 
OFF/TAPE with no cassette button pressed, to turn the unit off.
Using the PAUSE 
button on the cassette deck instead of the STOP/EJECT 
button to momentarily interrupt recording gives you a much cleaner sound recording.
USING THE CD
FUNCTION | CD door | ) PUSH |
|
|
|
|
|
|
| skip/search |
|
|
|
|
|
|
| backward |
|
|
|
|
|
| PUSH |
|
|
|
|
|
|
|
| skip/search |
REPEAT | REPEAT |
|
|
|
|
| forward |
| CD |
|
|
|
| STOP | |
|
| MOD |
|
|
| STOP 7 | |
|
| PL |
|
|
| ||
|
| RANDOM | E |
|
|
|
|
|
| Y |
|
|
| PLAY/PAUSE |
|
RANDOM |
|
| PROGRAM |
|
|
| |
|
|
|
|
|
| ||
|
|
| REMOTE | HBS | HBS |
| |
|
|
|
| SENSOR |
| ||
PROGRAM |
|
|
|
|
|
| PLAY/PAUSE |
|
|
|
|
|
|
|
LOADING A CD
1.Move FUNCTION to CD; “–
2.Press ) PUSH to open the CD door.
3.Place a CD into the tray with the label facing up.
4.Close the CD door. Then the total number of tracks appears.
5.To remove the CD, press ) PUSH, grasp the CD by its edges, and carefully pull it out.
| tape itself. |
• | Keep cassettes in their boxes when not in use. |
• | Cassette tapes can be erased by magnetic fields produced by magnets, electric motors, electrical transform- |
| ers, and other devices. Keep tapes away from magnets and magnetic fields. |
CLEANING THE TAPE HEADS
Iron oxide particles from the magnetic tape can build up on the parts that come in contact with the tape. These deposits can cause incomplete erasure, muffled playback sound, and might prevent automatic stop.
To clean a cassette deck, open the compartment door, press PLAY 
and gently clean the heads, capstan, and pinch wheel with a head cleaner.
Always unplug the power cord before cleaning, and allow 30 minutes drying time after using a liquid cleaner. Clean heads after every 25 hours of use.
•Demagnetize the head occasionally with a head demagnetizing cassette (available from many audio equip- ment stores).
•Never use any metal objects on or near the tape heads.
•Do not allow any cleaning material to fall into the tape assembly.
REMOTE FUNCTIONS (FOR CD OPERATION ONLY)
PLAY/PAUSE |
|
|
|
| STOP | When inserting batteries R03 | |
|
|
|
| Match the polarity (+ and | |||
|
|
|
|
|
| ||
SKIP |
| STOP | SKIP | and – markings in the battery compartment on the back | |||
SEARCH | P LAY | USE | of the unit. | ||||
(backward) | (forward) | ||||||
| PA | SEA |
|
| |||
|
|
|
|
| |||
PROGRAM | PROGRAM |
|
| REPEAT | REPEAT |
| |
|
|
|
|
| |||
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
IMPORTANT FOR LASER PRODUCTS
1.CLASS 1 LASER PRODUCT
2.CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.
3.CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.
4.REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.
CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS
DEFEATED. AVOID EXPOSURE TO BEAM.
VORSICHT ! UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZEN!
VARNING - OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
USING THE RADIO
TUNING IN RADIO STATIONS
Move FUNCTION to TUNER to turn the radio on.
•Set BAND to AM or FM.
•Tune in desired station by turning the TUNING knob.
•To turn off the radio, move FUNCTION to 
OFF/TAPE.
BEAT CUT/FM MODE SWITCH
•When recording an AM broadcast
When recording an AM broadcast, beats may occur. If this happens, set the switch to “1” or “2.”
•Changing the FM reception mode
When an FM stereo broadcast is hard to receive or noisy, set the switch to “MONO.”
Reception improves.
To restore the stereo effect, switch to “STEREO.”
BEAT CUT
1 
2
STEREO MONO
FM MODE
PLAYING A CD
Press PLAY/PAUSE 
to play all the tracks in order starting with track 1. The current track number appears in the display.
Note: Press PLAY/PAUSE 
to temporarily stop the CD. The 
indicator and the track number flash in the
display. Press PLAY/PAUSE 
again to resume playing the CD.
•Adjust VOLUME to a comfortable level.
•Press STOP 7 to stop playing the CD. Wait a few seconds for the CD to stop turning, then press ) PUSH to open the CD compartment door and remove the CD.
AUTOMATIC SEARCH
Automatic search lets you quickly locate the beginning of any track on the CD, including the track currently playing. If the CD is playing:
• Press 
(skip/search) once to return to the beginning of the current track, press twice to return to the beginning of the previous track.
•Press 
(skip/search) to skip to the beginning of the next track.
If the CD is stopped, repeatedly press |
| (skip/search) or |
| (skip/search) until the display shows the number |
|
| |||
of the track you want to play, then press PLAY/PAUSE |
| . The CD player starts playing the selected track. | ||
TRACK SEARCH
TROUBLESHOOTING TIPS
Problem | Solution | |
| • Make sure power cord is securely plugged into the AC power outlet (or that | |
System doesn’t turn on. | the batteries are fresh). | |
• Unplug the unit for a moment, and then plug it back in again. | ||
| ||
| • Check the outlet by plugging in another device. | |
|
| |
| • Adjust volume setting. | |
No sound | • Make sure you have selected the correct function: CD, TAPE, or TUNER | |
| and the headphones are disconnected. | |
|
| |
| • Adjust the FM telescopic antenna for better FM reception. | |
Poor radio reception | • Rotate the unit to achieve better AM reception. | |
• Try turning off electrical appliances near the unit, such as TV, hair dryers, | ||
| ||
| vacuum cleaners, or fluorrescent lights. | |
|
| |
| • Make sure the tray contains a CD. |
SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.
ADVARSEL - USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ
UDSÆTTELSE FOR STRÅLING.
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front: |
No obstructions and open spacing. |
USING THE TAPE
PAUSE – Press to interrupt tape play or record mode. Press a second time to resume tape play or tape record mode.
• In play mode, press and hold 
(skip/search) to move forward through a track at high speed.
• In play mode, press and hold 
(skip/search) to move backward through a track at high speed.
REPEAT
The REPEAT button allows you to repeat one track (REP 1) or all tracks (REP ALL). To scroll through the choices, continuously press and release REPEAT and check the display to see which choice you have selected. The following chart illustrates how REPEAT works in various modes.
NORMAL 
REP 1 
REP ALL 
CD doesn’t play. | • Make sure the CD’s label is facing up. | |
• Make sure that pause mode is not activated. | ||
| ||
| • Make sure CD function is selected. | |
|
| |
| • Clean the CD (as explained in “CARE AND MAINTENANCE”). | |
CD sound skips. | • Check CD for warping, scratches, or other damage. | |
• Check for vibration or shock that may affect the unit; move system if | ||
| ||
| necessary. | |
|
| |
Distorted or noisy | • Inspect the recording head and clean it if necessary. | |
• Demagnetize recording head (as explained in “CARE AND | ||
recordings | ||
MAINTENANCE”). | ||
|
2 | Sides/ Top/ Back: |
| No obstructions should be placed in the areas shown by the dimensions below. |
3 | Bottom: |
| Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a |
| height of 10 cm or more. |
Front view | 15 cm | Side view |
| 15 cm | |
15 cm | 15 cm | 15 cm |
|
| 15 cm |
| 10 cm | 10 cm |
STOP/EJECT 
– Press to stop the current tape activity, or to open the cassette compartment door when no buttons are active.
FF
– In stop mode, press to advance the tape toward the end. (When the tape reaches the end, press
STOP/EJECT 
to release the depressed button.)
REW 
– In stop mode, press to rewind the tape toward the beginning. (When the tape reaches the end, press
STOP/EJECT 
to release the depressed button.)
PLAY 
– Press to play cassettes.
REC 
– Press to record from the radio or CD player.
PLAYING A CASSETTE TAPE
1.Move FUNCTION to 
OFF/TAPE.
2.Press STOP/EJECT 
to open the cassette compartment door.
3.Insert a cassette tape into the compartment with the exposed part of the tape facing up and the side you want to play facing toward you.
4.Close the door securely.
5.Press REW 
or FF 
to move the tape to the desired starting point.
6.Press PLAY 
to begin playing the tape. The cassette tape plays until it reaches the end of the side, then it automatically stops.
RECORDING ON CASSETTE TAPES
You can record from the radio or the CD player.
For best recording, use normal bias tape.
•It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.
ERASE PROTECTION
RANDOM
Press RANDOM so that “RAND” appears in the display. Start play by pressing PLAY/PAUSE 
, and the tracks are played in random order.
To quit random play, press RANDOM again.
PROGRAMMING
Press PROGRAM to enter program edit mode.
“00” and “PROG” will flash in the display. Press 
(skip/search) or 
(skip/search) to select the track number and press PROGRAM to store the number in program place. You can repeat these steps to program up to 20 tracks. Note that programming more than 20 tracks will overwrite the tracks already programmed.
During program play, “PROG” lights steadily. To confirm the program order, press PROGRAM in stop mode. Each time you press PROGRAM, the program number appears, then the corresponding track number flashes in order from the first programmed track.
To clear the entire program in the memory, turn the unit off, or open the CD door.
This unit has been designed only to play back the following CDs.
•Digital audio CD
•Recordable digital audio CD
•Rewritable digital audio CD
When playing a CD-R or CD-RW
You can play back finalized
• You can play back | |
• | Some |
| stain on them, or if the player lens is dirty. |
• | The reflection factor of |
SPECIFICATION
CD player
CD capacity | : 1 CD |
Dynamic range | : 60 dB |
: 75 dB |
Tuner
Frequency ranges | : FM 88 - | 108 MHz |
| : AM 540 | - 1 600 kHz |
Antenna | : Telescopic antenna for FM | |
| Ferrite core antenna for AM | |
Cassette deck section
Frequency response | : 60 Hz - 10 000 Hz |
Wow and flutter | : 0.15% (WRMS) |
General
Speaker | : 9 cm cone ⋅ 2 (4 Ω) |
Power output | : 4 W (2 W + 2 W) at 4 Ω |
| (10% THD) |
Output terminals | : PHONES ⋅ 1 (∅ 3.5 mm, |
| stereo) |
Power supply | : AC 230 V Ó, 50 Hz |
| DC 9 V (“R20 |
| (13D)” ⋅ 6) |
Power consumption | : 12 W (at operation), 3 W (on |
| standby) |
Dimensions | : 420 mm (W) ⋅ 178 mm (H) ⋅ |
| 249 mm (D) |
Mass | : Approx. 3.2 kg (without |
| batteries) |
Accessories provided : AC power cord ⋅ 1 Remote control unit ⋅ 1 Batteries for the remote control unit R03
When you record new material, the cassette deck records over what- ever is on a tape. To protect a tape from accidental erasure, break off one or both plastic tabs (one for each tape side) on the top of the cassette tape. If you decide later to record on the tape, seal the hole with a piece of cellophane tape.
WARNING
A little bit of slack in your tape can cause scratches on the tape, or worse yet, the tape could break. If you notice some slack in the tape, use a pencil to tighten it up before you insert it in the tape deck.
TIP
to read. |
• |
Caution for DualDisc playback
The
Design and specifications are subject to change without notice.
The use of tapes longer than 120 minutes is not recommended, since characteristic deterioration may occur and these tapes easily jam in the
