GENERAL CONTROLS
TAPE OPERATIONS
Selecting the source to play
Slide the FUNCTION selector to select CD/USB, TAPE/ OFF, TUNER or AUDIO IN.
CD/USB:
To play back a disc or USB device. (See “DISC/USB OPERATIONS“ for operation.)
TAPE/ OFF:
To play back a cassette tape. (See “TAPE OPERATIONS“ for operation.)
•Once you start playing a tape, the power turns on.
TUNER:
To listen to the radio broadcast. (See “TUNER OPERATIONS“ for operation.)
AUDIO IN:
To playback an external device, such as a DAP (Digital Audio Player).
Function selector | Disc holder |
Volume knob
Radio controls
Tape controls
Disc / USB controls
AUDIO IN / USB terminal
Display | Cassette holder |
Playback procedure
1Set the source to TAPE/
OFF.
2 Open the cassette holder, then load a |
To stop playback
• The tape also stops when it reaches its end.
To pause playback
Recording on a tape
1Prepare the recording source.
•For the radio recording:
Set the source to TUNER and tune in to a desired station.
•For the disc or USB device recording:
-Set the source to CD/USB and load a disc or connect a USB device.
-Select a track or program the playback order if necessary. (See “Program playback.”)
•For AUDIO IN recording:
-Set the source to AUDIO IN and turn on an external device.
2Load a blank or erasable cassette. Use only a
3 Start recording. | |
• | 2 PLAY is also pushed down together with |
| the ¶ REC button. |
• | When recording from the disc/USB device, |
To use the beat-cut function
When recording an MW broadcast, beats may occur. In this case, slide the BEAT CUT switch on the rear to select the
NOTES
• It may be unlawful to record or play back |
copyrighted material without the consent |
of the copyright owner. |
• You can adjust the volume level while |
recording. The proper recording level is set |
automatically and it is not affected by the |
volume level. |
• If a TV is turned on and it is too close to the unit |
while recording, the recorded sound may have |
excessive noise. While recording, turn the TV off |
stereo mini plug (φ3.5 mm)
Play back a device after you have connected it. If the AUDIO IN sound is too quiet, turn that volume up.
•Refer to the instructions supplied with the device.
Adjusting the volume
Turn the VOLUME knob to increase or decrease the volume.
•Set the volume to minimum when you turn the unit on or start playing a tape.
Decrease
Increase
Turning the unit off
Slide the FUNCTION selector to TAPE/ OFF.
• You can play a tape even while the selector is set to TAPE/ OFF.
Listening with the headphones
Connect the headphones with the stereo mini plug (φ3.5 mm) to the PHONES jack on the rear.
stereo mini plug (φ3.5 mm)
•While the headphones are connected, no sound comes out from the speakers.
•Before connecting the headphones, make sure to turn down the volume.
cassette. |
ø Tape running direction |
3Close the cassette holder gently and start playback.
• To resume, press 8 PAUSE again.
To fast-forward/rewind a tape
or
•When the tape reaches its end, press § STOP/ EJECT to release 1 FF or ¡ REW.
playback of the disc/USB device starts at |
the same |
To stop recording
Press § STOP/EJECT.
Recording also stops when the tape reaches its end.
•For disc, USB device or AUDIO IN recording:
–If the tape reaches its end first, the playback of the disc/USB device pauses automatically. However, the playback of an external device continues.
–If the playback of the disc, USB device or external device stops first, recording continues. In this case, press § STOP/ EJECT to stop recording.
or keep the distance between the TV and the |
unit. |
Erasing a tape
Previous recording is overwritten when a new recording is made.
To erase a tape without making a new recording
1Set the source to TAPE/
OFF.
2Start erasing.
4Adjust the volume.
TUNER OPERATIONS
Improving the FM reception
When an FM stereo (FM ST) broadcast is hard to receive or noisy, select the monaural reception (MONO).
DISC/USB OPERATIONS
Main unit | Remote control |
Program playback
Up to 20 tracks can be programmed to play in a desired order.
To program the playing order
While playback is stopped...
1Show the program creation display.
Main unit Remote control
To edit the program
1While playback is stopped, press PROGRAM/ FOLDER repeatedly to select the program number of the track you want to replace.
•To add a track at the end of the program, press PROGRAM/FOLDER again when you reach the last program number. Then the next program number is shown on the
display.
• To restore stereo reception, switch to FM ST.
Basic procedure
When using the remote control, point at the remote sensor directly.
• Now you can select the first track of the program.
2Select a desired track.
Main unit | Remote control |
2Perform steps 2 to 3 on the left column to select a new track.
To erase the entire program
Press 7 while playback is stopped. The 
indicator disappears from the display.
• The entire program is also erased in the |
following cases: |
– when you open the disc cover. |
Basic procedure
1Set the source to TUNER.
2Select the band—FM/SW/MW.
Adjusting the antenna
3 Select a station.
FM/SW
Moves to indicate the current frequency
MW
The MW antenna is built in, so adjusting the position of the unit may help MW reception.
• In SW reception, you can finely tune in a desired station by turning the FINE TUNING knob.
4Adjust the volume.
1Load a disc or connect a USB device.
or
2Set the source to CD or USB.
Main unit | Remote control |
or | or |
The total number of tracks or folders
3Start playback.
Main unit Remote control
Lights only when 
playing an MP3 
file.
The current track number
4Adjust the volume.
To stop playback
Main unit | Remote control |
To pause playback | |
Main unit | Remote control |
•To resume, press the same button again.
•When a USB device is played back, 
indicator appears on the display.
•When a WMA file is played back, 
indicator appears on the display.
To select a track |
|
Main unit | Remote control |
or | or |
To select a folder (for MP3/WMA)
During playback...
1Show the folder selecting display.
Main unit | Remote control |
Folder number
2Select the desired folder while the 
indicator is flashing.
Main unit | Remote control |
or | or |
|
To locate a desired position on the disc
During playback... |
|
Main unit | Remote control |
or | or |
Press and hold | Press and hold |
or | or |
3Add the track to the program.
Main unit | Remote control |
• | The next program |
| number flashes on the |
| display. |
4Repeat steps 2 to 3.
5Start playback.
Main unit | Remote control |
•If you press 7 while you are programming tracks, the programmed order is erased.
– when the unit is turned off. |
– when you select another source. |
– when you disconnect the USB device. |
Repeat/Random playback
Select the desired playback mode.
Main unit | Remote control |
Each time you press the button, the playback mode changes as follows:
Indicator | Playback mode | ||
|
|
|
|
|
|
| Repeats a single track/file.* |
|
|
|
|
|
|
| Repeats files in a folder. (For |
|
|
| |
|
|
| MP3/WMA only) |
|
|
|
|
|
|
|
|
|
|
| Repeats all tracks/files.* |
|
|
|
|
|
|
| Plays tracks/files at random. |
|
|
|
|
•To cancel, press the same button repeatedly until the indicator above disappears from the display.
*Repeat playback is also available during program playback.