GENERAL CONTROLS
Volume knob and | Disc holder |
| |
function selector | Radio controls |
Display
Disc controls
TUNER OPERATIONS
Basic procedure
1 Set the source to TUNER. | 3 Select a station. |
Improving the FM reception
When an FM stereo (FM ST) broadcast is hard to receive or noisy, select the monaural reception (MONO).
• To restore stereo reception, switch to FM ST.
Adjusting the antenna
FM | AM |
| The AM antenna is built in, so adjusting the |
| position of the unit may help AM reception. |
Selecting the source to play
Slide the FUNCTION selector to select CD, TUNER | CD: | |
or AUDIO IN. | To play back a disc. (See “DISC OPERATIONS.”) | |
|
| TUNER: |
|
| |
|
| |
|
| To listen to the radio broadcast. (See “TUNER |
|
| OPERATIONS.”) |
|
| AUDIO IN: |
|
| To listen to the other equipment connected to |
|
| the AUDIO IN jack. (See “LISTENING TO OTHER |
|
| EQUIPMENT.”) |
Adjusting the volume |
| Turning the unit off |
Turn the VOLUME knob to increase or decrease the | Slide the FUNCTION selector to OFF. | |
volume. |
|
|
• Set the volume to minimum when you turn on the |
| |
unit. |
|
|
Decrease | Increase |
|
2 Select the | Moves to indicate the |
| current frequency |
4 Adjust the volume.
DISC OPERATIONS
Program playback
Up to 20 tracks can be programmed to play in a desired order.
To program the playing order
While playback is stopped...
1Show the program creation display.
4
5
Repeat steps 2 and 3.
•When the 20th track is programmed, “- -
Start playback.
Repeat/Random playback
Select the desired playback mode.
Playback mode indicator (See below.)
Each time you press the button, the playback mode changes as follows:
LISTENING TO OTHER EQUIPMENT
Basic procedure
1 Load a disc. | 4 Adjust the volume. | To select a track | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To locate a desired position on the disc
During playback...
2 Set the source to CD.
To stop playback
Program number
•Now you can select the first track of the program.
2Select a desired track.
3 Add the track to the program. |
•After program playback ended or stopped, the program playback mode is automatically canceled. (The PROGRAM indicator disappears from the display.)
To play back the program again, press PROGRAM, then PLAY/PAUSE 6.
To edit the program
1While playback is stopped, press PROGRAM repeatedly to select the program number of the track you want to replace.
•To add a track at the end of the program, select the last program number.
2Perform steps 2 and 3 on the left column to select a new track.
To erase the entire program
Indicator | Playback mode |
|
|
REPEAT | Repeats the current track. |
|
|
REPEAT ALL | Repeats all tracks. |
|
|
RANDOM | Plays tracks at random. |
|
|
To cancel, press the same button repeatedly until the indicator above disappears from the display.
•Repeat playback is also canceled if the playback is stopped.
•Random playback cannot be used during program playback. If you program the playing order during random playback, random playback is canceled.
Basic procedure
1Turn the volume to minimum.
3
4
Set the source to AUDIO IN.
Start playing the equipment.
Press and hold
The total number of tracks
3Start playback.
To pause playback
The current track |
|
number | • To resume, press the same button again. |
|
• The next program number appears on the |
display, then track selection display is shown. |
Program number |
While playback is stopped...
1Press PROGRAM.
•PROGRAM indicator lights up on the display. 2 Press 7.
•The entire program is also erased in the following cases:
–when you open the disc holder.
–when the unit is turned off.
–when you select another source.
2 Connect the equipment. | 5 Adjust the volume. |
•Connect the equipment with the stereo mini plug (3.5 mm (3/16 in) diameter) to
the AUDIO IN jack on the rear.