Adjustment of Indicator's Brightness
The brightness of the indicator light on the control panel can be adjusted in five levels.
Indicators for which brightness cannot be adjusted:
● [CALL] button
● [PREVIEW] button ● [TALLY] indicator
1 Set the [LOCK] switch to AOFFB.
OPERATE |
|
| LOCK |
|
| BARS |
|
|
| PART |
|
|
|
|
|
| OFF FULL |
|
|
|
|
| SCENE FILE |
|
|
| SPEED |
1 | 2 | 3 | 4 | 5 |
|
|
| PART |
| SHUTTER |
|
|
|
NORMAL | 1/100 | 1/250 | 1/1000 | 1/2000 | VARIABLE | |
1/120 | 1/500 |
2 Press and hold the [BARS] button, and operate the [IRIS/AUTO IRIS LEVEL] lever at the same time.
●Doing so switches to the brightness adjustment mode, and the brightness of the indicator light changes.
| OPERATE |
|
| LOCK |
|
| BARS |
|
|
|
| PART |
|
| Press and |
|
| SCENE FILE | OFF FULL |
| |||
|
|
|
|
| SPEED | ||
| 1 | 2 | 3 | 4 | 5 |
| hold |
|
| PART |
| SHUTTER |
|
|
|
| 1/100 |
|
|
| VARIABLE | ||
NORMAL | 1/120 | 1/250 | 1/500 | 1/1000 | 1/2000 | ||
button that | 0dB | 3dB |
| GAIN |
|
|
|
6dB | 9dB | 12dB | 15dB | 18dB | |||
enables | ALC | LOLUX | VARIABLE | LEVEL | |||
| |||||||
brightness | LEVEL | GAMMA | LEVEL | DETAIL | KNEE POINT | AUTO | |
|
|
|
|
|
|
| KNEE |
adjustment | BLACK |
| WHITE BALANCE MODE |
| |||
| COMPRESS | STRETCH | MANUAL | PRESET | FAW | AW A | AW B |
| R | WHITE PAINT |
| PAINT | AUTO WHITE | ||
|
| B |
|
|
|
| |
| R | BLACK PAINT |
| PAINT | AUTO BLACK | ||
|
| B |
|
|
|
| |
|
|
|
| PART |
|
|
|
|
|
|
| OVER |
| OPEN | |
| PRESET | PRE |
| IR |
| IS Lever | |
| LEVEL | IRIS MODE |
|
|
|
| |
|
|
| FULL | AUT |
|
| |
|
|
|
|
|
| ||
|
| SET | AUTO | LEV |
| Operation | |
|
| FULL |
|
|
| ||
|
| TALLY |
|
|
|
|
|
| CALL | PREVIEW | UNDER |
|
| ||
|
|
|
|
| CLOSE | ||
|
|
|
|
|
| MASTER |
|
|
|
|
|
|
| BLACK |
|
Note:
●Normal operation is disabled when in the brightness adjustment mode. However, the [OPERATE] button remains enabled.
3 Determine the brightness level.
●Releasing the [BARS] button upon selecting a random brightness level restores the normal mode, and the corresponding brightness level is stored.
Input/Output of Rear Ports
The tally circuit comes with two input systems, namely contact input and open collector input.
This is set to contact input in the factory settings. You can change this to open collector input via settings of the DIP switch at the side of the main unit.
Remove the cover at the side of this product, and set the tally circuit supply system using DIP switch no. 6. (A 24 page)
22