JVC manual

MICRO COMPONENT SYSTEM

UX-N1S

Mains (AC) Line Instruction(not applicable for Europe, U.S.A., Canada, Australia, Hong Kong and U.K.)Adjusting the voltage selector

Use a screwdriver to slide the voltage marker so that it is set to the same voltage as where you are plugging in the unit.

Bottom of the unit

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1.Front: No obstructions and open spacing.

2.Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.

3.Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.

Front view		Side view
15 cm	15 cm	15 cm
		15 cm

Basic and Common Operations

Operating on the System		Using Headphones
		Be sure to turn down the volume before connecting or wearing
To	Press
		the headphones.
Turn on or off (standby) the	The STANDBY lamp on the System turns off/	• Connecting the headphones will deactivate the speakers.
power	on.

Operating on the Remote Control

To	Press
Turn on or off	The STANDBY lamp on the System turns off/
(standby) the power	on.

See “Playing Back Discs” on page 4.

—Consists of CA-UXN1S and SP-UXN1S

UX-N1W

—Consists of CA-UXN1W and SP-UXN1W

1 cm	1 cm
		15 cm
	10 cm
SP-UXN1S/SP-UXN1W CA-UXN1S/CA-UXN1W SP-UXN1S/SP-UXN1W		CA-UXN1S/CA-UXN1W

About the cooling fan

Select a source*

See “Playing Back Discs” on page 4.

See “Listening to FM and AM Broadcasts” on page 5.

See “Connecting a Portable Audio Device” on page 6.

Select a source	See “Listening to FM and AM Broadcasts” on
	page 5.

See “Connecting a Portable Audio Device” on page 6.

A cooling fan is mounted on the rear panel of the unit to prevent abnormal temperature inside the unit, thus assuring normal operation of the unit.

Adjust the volume

You can adjust the volume level from level 0 (VOL MIN) to level 31 (VOL MAX).

Adjust the volume

You can adjust the volume level from level 0 (VOL MIN) to level 31 (VOL MAX).

INSTRUCTIONS

GNT0065-018A[US/UB/A/UW/UJ] 0306MOCMDWJSC

©2006 Victor Company of Japan, Limited

Warnings, Cautions and Others

Caution —		button!
Disconnect the mains plug to shut the power off completely.
When installing the apparatus, ensure that the plug is easily
accessible.
The	button in any position does not disconnect the
mains line. The power can be remote controlled.

•When the unit is on standby, the STANDBY lamp lights red.

•When the unit is turned on, the STANDBY lamp goes off.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1.Do not remove screws, covers or cabinet.

2.Do not expose this appliance to rain or moisture.

CAUTION:

•Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

•Do not place any naked flame sources, such as lighted candles, on the apparatus.

•When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

•Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

AC 110V 220-240V

Voltage marker

Caution for mains (AC) line

BEFORE PLUGGING IN, check that your mains (AC) line voltage corresponds with the position of the voltage selector switch on the bottom of the unit and, if different, set the voltage selector correctly to prevent

any damage or risk of fire/electric shock.

CAUTION:

DO NOT plug in before setting the voltage selector and all connection procedures are complete.

IMPORTANT FOR LASER PRODUCTS

1.CLASS 1 LASER PRODUCT

2.CAUTION: Do not open the top cover. There are no user serviceable parts inside the System; leave all servicing to qualified service personnel.

3.CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.

[European Union only]

The model information is located on the bottom.

Precautions

Notes on the power cord

•When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet. A small amount of power (5.0 W) is always consumed while the power cord is connected to the wall outlet.

•When unplugging the System from the wall outlet, always pull the plug, not the power cord.

•Do not handle the power cord with wet hands.

•Disconnect the power cord before cleaning the System or moving the System.

•Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.

•If the cord is damaged, consult a dealer and have the power cord replaced with a new one.

Avoid moisture, water, dust, and high temperatures

•Do not place the System in moist or dusty places.

•If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using the System in this state may cause a fire or electrical shock.

•Do not expose the System to direct sunlight or place it near a heating device.

Notes on installation

•Select a place which is level, dry and neither too hot nor too cold between 5˚C and 35˚C.

•Do not install the System in a place subject to vibrations.

•Do not put heavy objects on the System.

To prevent malfunction or damage of the System

•Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.

•Do not block the vents.

To clean the cabinet

•Use a soft cloth. Follow the relevant instructions on the use of chemically-coated cloths.

•Do not use benzene, thinner or other organic solvents and disinfectants. These may cause deformation or discoloring.

There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.

*You can operate the source select buttons on the System only touch lightly, because these buttons are “touch sensor panel.”

If you touch any one of these buttons, they lights in blue briefly.

Point it at the remote sensor on the front panel. (The operating range is approx. 7 m.)

				STANDBY lamp
NOTE	Display Information
DO NOT turn off (standby)
the System with the volume
set to an extremely high level;	Disc play mode indicators (See page 4.)
Otherwise, the sudden blast		Tuner mode indicators			Timer mode indicators
of sound can damage your
			(See page 5.) (See the right column and page 5.)
hearing, speakers and/or
headphones when you turn
on the System or start
playback.

QP Link indicator	Main Display
(See page 6.)

AHB PRO and A.STBY indicator (See the right column.)

Drop the volume in a		To restore the volume, press again, or adjust
moment		the volume level.
Reinforce the bass		AHB PRO indicator appears on the display.
sound		To cancel this function, press again.
		Press once to adjust the bass level or press
		twice to adjust the treble level.
Adjust the tone (Bass/		Then press VOLUME + to increase the level or
Treble)		press VOLUME – to decrease it.
		• You can adjust the bass and treble level from
			–3 to +3.
Changing the display		Press when the System is turned on.
brightness		To cancel this function, press again.
		Press and hold for more than 2 seconds when
		the System is on standby.
Set the Save mode		To cancel this function, press and hold for
		more than 2 seconds again.
		• Setting the Save mode allows you to reduce
			power consumption by turning the display
			off while on standby.
Changing the display		Press briefly (except for FM mode).
information (Clock
		For setting the clock, see page 5.
and Source)
Turn off the System		Press and hold until A.STBY indicator appears
		on the display.
automatically after CD
playback is over		To cancel this function, press and hold again.
(AUTO STANDBY		• If no operation is done for about 3 minutes
function)
			after CD playback stops, the System turns off.
		Press briefly and repeatedly to specify the time
		(in minutes) as follows:
Turn off the System by	10		20	30		60	90	120	150
using the sleep timer					Canceled

•To check the time remaining until the shut-off time after setting the sleep timer, press SLEEP once.

1

3

Getting Started

Supplied Accessories

After unpacking, check to be sure that you have all the following items. The number in parentheses indicates the quantity of each piece supplied.

•Remote control (x 1)

•Lithium coin battery CR2025 (x 1) (The battery has been installed when shipped from the factory.)

•AM loop antenna (x 1)

•FM antenna (x 1)

•AC plug adapter (x 1) (except for Hong Kong and Australia)

If anything is missing, consult your dealer immediately.

Prepare the Remote Control

When you use the remote control	Insulation sheet
for the first time, pull out the
insulation sheet.

Replacing the Battery in the Remote Control

Insert the battery into the	Lithium coin battery
remote control by matching the	(product number: CR2025)
polarity (+ and –) correctly.

NOTES

•Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately.

•Do not recharge, short, disassemble or heat the battery or dispose of it in a fire. Doing any of these things may cause the battery to give off heat, crack, or start a fire.

•Do not leave the battery with other metallic materials. Doing this may cause the battery to give off heat, crack, or start a fire.

•When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may start to give off heat, crack, or start a fire.

•Do not poke the battery with tweezers or similar tools. Doing this may cause the battery to give off heat, crack, or start a fire.

•Dispose of battery in the proper manner, according to federal, state, and local regulations.

CAUTION:

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

Playing Back Discs

This System can play back the following discs—regular CD and CD-R/CD-RW (recorded either in the audio CD or MP3 format).

• When playing back the MP3 track, MP3 indicator appears on the display.

To Set a Disc

1 On the System 2 3 On the System

The disc cover on the	Place a disc correctly with its label side up, then	The disc cover on the
	press down on the portions around the disc’s
System opens.		System closes.
	center hole until you hear a click.
		• Do not close forcibly
	• When removing the disc, take out the disc

Programming the Playing Order—Program Play (except for MP3)

1	Press repeatedly until the PRGM (program) indicator
	appears on the display before you start playback.

2 or Select the track number to program.

3 Press to program the selected track.

Repeat step 2 and 3 to program other tracks you want.

4• If you try to program a 33rd track, “FULL” will appear on the display.

Connections

Do not connect the AC power cord until all other connections have been made.

by holding it at the edge with pressing the	the disc cover with
	the hand.
System’s pivot lightly.

5	The tracks are played in the order you have
	programmed.
	Operations on the Program Play Mode

NOTES
• Make sure the antenna conductors do not touch any other terminals,			AM loop antenna
connecting cords and power cord. Also, keep the antennas away from
			(supplied)
metallic parts of the System, connecting cords, and the AC power cord.
	FM antenna (supplied)		Turn it until the best
This could cause poor reception.
			reception is obtained.
• If the cords are covered with vinyl, remove the vinyl to expose the tip
	Extend it so that you can obtain the best reception.
of the cord by twisting the vinyl.
		To connect the AM loop antenna
		1 Hold
		2 Insert	3 Release
	PHONES	SPEAKERS
	RIGHT	LEFT	COAXIAL
			ANTENNA
			LOOP
			AM EXT
		IMPEDANCE
		MIN

To assemble the AM loop antennaFor better FM/AM reception Outdoor FM antenna

(not supplied)

Disconnect the supplied FM antenna, and connect to an outdoor FM antenna using a 75 Ω wire with coaxial type connector.

Vynile-covered wire (not supplied)	AM loop antenna
Extend it horizontally.
	Keep it connected.

Basic Disc Operations

			Press
To	On the	On the
	System	remote
			Current track number and elapsed playing
Playback the disc			time appear on the main display.
			• During playback, press again to stop
			playing for a moment.
			• While playback is stopped, total track
Stop playback			number and total playing time (for MP3
			disc, group number and track number)
			appear on the main display.
			Increases the track numbers.
Select a track
			Decreases the track numbers.
	—		Increases the group numbers while playback
Select a group (MP3			is stopped.
only)	—		Decreases the group numbers while playback
			is stopped.
			Fast-forwards the track by pressing briefly.

Playing Repeatedly—Repeat Play

Press repeatedly before you start playback to specify the repeat mode as follows:

REP 1	REP GRP
	(MP3 only)
REP OFF	REP ALL

To		Press
Check the	or
programmed		Press while playback is stopped.
contents

To erase the last step

To erase

the entire Press while playback is stopped. program

	Press twice while playback is
To exit from	stopped to exit from the program
program play	play.
	• The stored program is erased.

	Playing at Random—Random Play
1	Press until the RND (random) indicator appears on
	the display before you start playback.
2	Playback starts in random order.
	Random Play ends when all tracks are played.
	Operations on the Random Play Mode

To connect the speaker cords	NOTES
Make sure the both speakers are connected	• DO NOT connect more than one speaker
	to each terminal.

	—
Forward search /	To stop searching, press 6.
Reverse search	Fast-reverses the track by pressing briefly.

1	REP 1	Repeats the current (or specified)
		track.

To Press

To a wall outlet	correctly and firmly.	• DO NOT allow the conductor of the
	When connecting the speaker cords, match the
Plug the AC power cord only after
		speaker cords to be in touch with the
	polarity of the speaker terminals: white cord to (+)

—

To stop searching, press 6.

REP GRP

Repeats all tracks in the current group. (MP3 only)

To skip a track • 4 does not work.

all connections are complete.	and white cord with black stripe to (–).	metallic parts of the System.
• If the wall outlet does not match

NOTES

• If the disc cannot be read correctly (because it is scratched, for example) or an unreadable CD-R or

REP ALL Repeats all tracks.

REP OFF Normal playback

To exit from

Press once while playback is stopped to exit from the random

the AC plug, use the supplied AC		3 Release
plug adapter. (except for Hong	1 Hold
		2 Insert
Kong and Australia)

CD-RW is loaded, playback will not start.

• If no disc is inserted, “NO DISC” appears on the main display.

2

random play

play.

2 4