Operations
Front view
Power lamp
Rear view
The unit automatically accommodates AC power between 110V and 240V. You do not need any setting to match the unit with your local power voltage.
Turning On the Power—POWER Å
Press the ON [ ❙ ] portion of the POWER switch.
The main power turns on and the power lamp in the front panel lights in green.
• The power lamp lights in red when the Auto Power On/Standby places the
unit into standby mode.
To completely cut off the power to this unit
Press the OFF [ ‡ ] portion of the
POWER switch.
This will disconnect the mains lead.
Adjusting the Volume—VOLUME ı
Adjust the volume output level through this unit while comparing with the sounds coming out of the main (front) speakers.
•Once you have adjusted the volume output level of this unit, you do not need to adjust it each time you use this unit. Adjusting the volume level on the connected amplifier will also adjust the volume level through this unit.
1 Turn the VOLUME knob to the MIN position. | VOLUME |
| MIN |
| MAX |
2 Turn on the connected amplifier and start playing a source. Playback sounds come out of the main (front) speakers and this unit.
3 Adjust the VOLUME knob to obtain a well- | VOLUME | |||
balanced sound level with that of the main | MIN | |||
(front) speakers. |
|
|
| |
MAX | ||||
|
If your amplifier is not provided with a crossover frequency setting:
1 Press out the CUT OFF FILTER button to set it | CUT OFF FILTER | ||||
to the — VARIABLE position. |
|
|
|
| VARIABLE |
|
|
|
| ||
Now the FREQUENCY knob is activated and you |
|
|
|
| FIX |
|
|
|
| ||
|
|
|
|
| |
can adjust the crossover frequency on this unit. |
|
|
|
|
|
2 Turn the FREQUENCY knob to obtain the | FREQUENCY |
best matching crossover frequency with
your main speakers. | 50Hz | |
| ||
Adjust the frequency (50 Hz to 200 Hz) while | 200Hz | |
listening to playback sound coming out of both | ||
| ||
the main speakers and this unit. |
|
•If your main speakers can reproduce the bass sound well, adjust the frequency at a lower level.
•If you feel bass sounds are not sufficient, adjust the frequency at a higher level.
Changing the Phase—PHASE Î
You can change the sound phase to match your preference. Select either “NORMAL” or “REVERSE” to obtain a better bass sound.
Press in or out the PHASE button to select either | PHASE | ||||
the NORMAL position or the REVERSE position. |
|
|
|
| NORMAL |
|
|
|
| REVERSE | |
|
|
|
| ||
• NORMAL : Normally select this. |
|
|
|
|
|
•REVERSE : Select this when you feel the bass sound is better with this mode rather than with “NORMAL.”
Operating the Unit Automatically According to the Incoming
By using this function, this unit automatically enters standby mode even though the POWER switch is turned ON [ ❙ ].
Press the AUTO POWER ON/STANDBY | AUTO POWER ON / STANDBY | ||||
button to the — ON position. |
|
|
|
|
|
|
|
|
|
| ON |
|
|
|
|
| |
|
|
|
|
| CANCEL |
|
|
|
|
|
ı
VOLUME
Î
PHASE
‰
AUTO POWER ON/STANDBY
Å
POWER
VOLUME | FREQUENCY |
| |
MIN | 50Hz |
| Ç |
|
| ||
MAX | 200Hz |
| |
|
| ||
PHASE |
| CUT OFF FILTER | FREQUENCY |
|
| ||
| NORMAL | VARIABLE |
|
| REVERSE | FIXED | Ç |
AUTO POWER ON/STANDBY |
|
ON | RIGHT LEFT/MONO | CUT OFF |
CANCEL | INPUT 1 | FILTER |
| ||
|
| |
RIGHT | LEFT |
|
| INPUT 2 |
|
|
| |
| TO MAIN |
|
| SPEAKERS |
|
RIGHT | LEFT |
|
POWER
OFF ON
If the volume is set at a high level before starting play, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.
Adjusting the Crossover Frequency
You can adjust the crossover frequency to determine the bass sound level this unit handles.
•Once it is set, only the sounds below the frequency come out of the
When the main speakers in use are JVC’s
Press in the CUT OFF FILTER button to set it to the | CUT OFF FILTER | ||||
_ FIX position. |
|
|
|
| VARIABLE |
|
|
|
| ||
|
|
|
| ||
|
|
|
|
| FIX |
|
|
|
|
|
•The FREQUENCY knob is deactivated.
•When your amplifier is equipped with crossover frequency setting, set it within the range of 100 Hz to 150 Hz.
•When your amplifier is equipped with speaker size setting, select “small.”
•If no sound comes in for about 10 minutes, the unit automatically enters standby mode. The power lamp lights in red. Then if the unit detects incoming signals, this unit starts operating automatically (the power lamp now lights in green).
If Auto Power On/Standby does not work | AUTO POWER ON / STANDBY | |||||
correctly (see “MEMO” below), press out the |
|
|
|
|
| |
AUTO POWER ON/STANDBY button to set it to |
|
|
|
| ON | |
|
|
|
| |||
the _ CANCEL position. Auto Power On/ |
|
|
|
| CANCEL | |
|
|
|
| |||
Standby is canceled. |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
When the volume level of the amplifier is so low or the incoming signals are so weak that this unit cannot detect sounds, Auto Power On/Standby may not work correctly.
•This unit may enter standby mode even though signals are coming in.
•This unit may not start operating after entering standby mode, even though signals start coming in.
Additional Information
Speaker layout
To obtain the best possible sound from your unit:
Left front | Right front | Subwoofer |
speaker | speaker |
|
| Center |
|
| speaker |
|
| Listening position |
|
Left surround | Right surround | |
speaker | speaker |
Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your dealer.
Symptom |
| Possible Cause |
| Action | ||
Power does not come on. | Is the unit pugged in? | Plug the AC power cord firmly into the AC | ||||
|
|
|
|
|
| outlet. |
|
|
|
|
| ||
Auto Power On/Standby does not | Signals are too weak or volume | This is not a malfunction. If this happens, cancel | ||||
function correctly. | level is too low. |
|
|
| Auto Power On/Standby. | |
|
|
|
|
| ||
No sound is heard. | Is the VOLUME knob turned to the | Turn the VOLUME knob until a suitable volume | ||||
|
| MIN position? |
|
|
| is found. |
|
|
|
|
| ||
|
| Connections are incorrect, or loose. | Check the connections. If incorrect, redo the | |||
|
|
|
|
|
| corrections. |
|
|
|
|
| ||
|
| Audio signals through the amplifier | Increase the volume level on the amplifier. | |||
|
| are extremely weak. |
| |||
|
|
|
|
| ||
Sounds fluctuate (suddenly become | The | Lower the volume level on the amplifier so that | ||||
loud or soft). | working. |
|
|
| the symptom will not occur. | |
|
|
|
|
| ||
Suddenly no sound comes out. | The VOLUME knob on the rear is | Turn down the volume, then turn off and on this | ||||
set to a very high level. | unit. | |||||
|
|
|
|
| ||
Suddenly no sound comes out. | The volume of the playback source | Turn down the volume of the playback source, | ||||
is too high. |
|
|
| turn off and on the source, then adjust the | ||
|
|
|
|
|
| volume properly on the source. |
|
|
|
|
|
|
|
Specifications |
|
|
|
|
| |
|
| Type | : | Powered Subwoofer | ||
|
|
|
| |||
|
| Speaker unit | : | 16.0 cm cone (⋅ 1) |
| |
Frequency range | : | 30 Hz to 200 Hz |
| |||
Input impedance | : | 50 kΩ | ||||
Input terminals | : | INPUT 1 | ||||
Power requirements | : | AC 110 V | , 50 Hz/60 Hz | |||
Output power of | : | 100 W (45 Hz, 4 Ω, 10 % THD) | ||||
Power consumption | : | 27 W |
| |||
|
| Dimensions | : | 217 mm (width) ⋅ 393 mm (height) ⋅ 376 mm (depth) | ||
|
| Mass | : | 9.2 kg |
| |
|
| Accessories | : | Monaural audio cord (⋅ 1), AC plug adaptor (⋅ 1) |