Assembly

7 Assembling the satellite speakers

3 Fix the leg to the stand with three of the supplied
Each speaker (except the center speaker) has been divided into

screws —long: M4 x 25 mm (M4 x 1 in.).

three parts for shipment. Before using this speaker system,

Leg

assemble it first by following the procedure below.
2)Insert the tips of the speaker cord into the leg and pull
them out as illustrated.

Do not pull or remove the cord protector, otherwise the speaker cord may come off from terminal on the leg or the speaker may be damaged.

Stand

Leg

Speaker section
Speaker cordCord protector
Speaker

Screw

 

section
Leg
Stand
LegLeg
3) Insert the speaker cord into the speaker terminal inside the leg.
• Prepare a Phillips screw driver.
Before assembling—

•Take care not to drop the stand while assembling; otherwise, it may cause damage to the floor or injury.

•Ensure enough space for assembly and installation.

•Place a large, thick cloth on the floor where you assemble the speaker, so you can protect the floor and the speaker itself.

•Use the speaker only after assembly is fully and correctly done.
Attaching the leg and the stand

1 Remove the terminal cover from the leg.

First remove the screw on the terminal cover, then detach the cover by pulling it upward.

•You will need to use the removed screw in step 5.
•Do not tighten each screw completely one by one.First put all screws in, then tighten them evenly and firmly.It is recommended to place a cushion under the leg.• You can tighten the screws easily by placing the leg horizontally.Cushion

 

1 Press
Black

 

 

Red

 

2 Insert

Black

Copper
striped
3 Release

Leg

5 Attach the terminal cover to the leg.

7 Join the speaker section and the leg.

Insert the speaker section to the leg, then fix the speaker section and the leg with one of the washers and one of the supplied screws—short: M5 x 12 mm (M5 x 1/2 in.).

•Push cords fully inside the leg before attaching the speaker section.

Speaker section

Joint here without gap.Leg Washer Screw

Screw

Terminal cover

Leg

4 Connect the speaker cord to the speaker terminal of the leg.

•Use the 6-meter (19.7 ft) speaker cords for front speakers and 15-meter (49.2 ft) speaker cord for rear speakers.

•Each speaker cord has its name tag attached to one end. Attach the end without the name tag to the speaker terminal.

•Twist and remove the insulation at the end of each speaker cord before connecting.

Tag

Push cords fully inside the leg. Then fix the terminal cover using the screw removed in step 1.

Screw

Terminal cover

8 Repeat the procedure from step 1 to assemble the other satellite

speakers.

For disassembly
Reverse Assembly procedure:
1)Remove the speaker section from the leg.
2)Remove the leg from the stand.

7Connecting the center speaker

• To connect the center speaker, use the same type of speaker

2 Join the leg to the stand.

•Rotate either the leg or stand so that the mark on the legand the mark on the stand are facing the same direction.

•Make sure to match the screw holes on the leg with those on the stand so that they are aligned correctly.

mark

Leg

To the speaker terminal of the leg
1) Insert the speaker cord inside the stand as illustrated.
• Pull the speaker cord out of the center of the stand by
about 50 cm (20 in.).
Joining the leg and the speaker unit

6 Insert the speaker cord into the speaker terminal inside the leg.

cord (6 m (19.7 ft); tagged with “CENTER”) as used for
connecting the front speakers.
• Twist and remove the insulation at the end of each speaker cord
before connecting.

Insert the speaker cord into the speaker terminal.

1 Press

2 Insert

3 Release

Stand

The cord with the black stripe is on this side as illustrated.

Speaker

1 Press

section

 

Red

 

Black

2 Insert

 

Copper

 

Stand

mark

Black striped

3 Release

Black

 

Black striped

Leg

Copper Red