JVC TK-WD310 Others, Factory Settings screen, Troubleshooting, Specifications

Allowed characters

MENU SETTING

FACTORY SETTINGS screen

Returns set values to their factory settings.

8 direction (SELECTOR button) t direction

Space

Pressing the SELECTOR button in the t direction will select the character on the right and pressing in the 8 direction will select the character on the left. Pressing and holding the button will continu- ously change the character selected.

Memo

When CAMERA TITLE is set to ON, a background the width of 1 character is displayed, even when there is no camera title entered. If a CAMERA TITLE of more than 1 character is entered, a back- ground the width of 24 characters is displayed.

— — — M E N U — — —

F OC U S A D J U S T . .

V I D E O A D J U S T . .

C AM E R A S E T T I N G S . .

F A C T O R Y S E T T I N G S . .

E X I T

Cursor

— — — F A C T OR Y S E T T I N G S — — —

C A N C E L

CL E A R

Operation

1.Display the FACTORY SET- TINGS screen. ( Page 24)

2.Press the SELECTOR button in the vertical direction (6 or 7) and move the cursor (>) to

CLEAR.

3.Press the SET button.

●Settings including the camera title will be restored to the fac- tory settings and the screen will return to the MENU screen.

*Select CANCEL and press the SET button to return to the MENU screen without chang- ing settings.

4.Exit the menu screen.

Select EXIT within the MENU screen and press the SET but- ton to return to the normal screen.

38

39

OTHERS

Troubleshooting

Symptom		Remedy
The operation becomes un-	Drop in voltage of the power supply can
stable	be considered. Check the length and
	thickness of the power supply cable.
	( Page 17)
The auto iris will not operate	Set the VIDEO/DC switch on the side
	of unit according to the type of auto iris
	lens used.
	( Pages 20, 21)
There is noise in the screen	Lower the gain using the AGC MODE
or increase in residual im-	menu item.
ages	ULTRA SUPER HIGH MID		LOW OFF
	(MAX)			(MIN)
		Gain
	( Page 31)
The colors of the screen are	When using in an environment where
not natural	there are changes in the light source,
	set the WHITE BALANCE menu item
	to ATW.
	( Page 33)
White balance adjusted	Set the WHITE BALANCE menu item
automatically/manually	to AWB or MANUAL.
cannot be used	( Page 33)
The camera title will not ap-	Set the CAMERA TITLE menu item to
pear	ON.
	( Page 36)
The vertical phase cannot be	When adjusting the vertical phase dur-
adjusted using the V PHASE	ing line lock, set the LL/INT switch on
menu item	the back of unit to LL.
	( Page 11)

OTHERS

Specifications

Image pickup device	: 1/3 type WDR digital image device
Number of effective pixeis	: 380,000 pixels ((H) 720 ⋅ (V) 540)
Synchronizaton method	: Internal,Line lock
Scanning frequency	: U Type (H) 15.734 kHz, (V) 59.94 Hz
	E type (H) 15.625 kHz, (V) 50.0 Hz
Resolution	: 480 TV lines (H)
VIDEO OUT	: Composite video signal
	1 V(p-p), 75Ω (BNC)
Video S/N ratio	: 50 dB (AGC OFF)
Minimum required illumination	: 1.9 lx (50%, F1.2, AGC HIGH)
	0.5 lx (50%, F1.2, AGC ULTRA(⋅16))
	0.95 lx (25%, F1.2, AGC HIGH)
	0.25 lx (25%, F1.2, AGC ULTRA(⋅16))
Lens mount	: CS mount
Power supply	: AC 24 V ` 50 Hz/60 Hz
	DC 12 V
Power consumption	: U type Approx. 5.7 W
	E type Approx. 400 mA
Ambient temperature	: –10°C to 50°C (operation)
	0°C to 35°C (recommended)
Mass	: 330 g
Accessory	: Instructions
	U type	1
	E type	2
	Ferrite core	1

External Dimensions (Unit: mm)

U1-32		107
50		95
50	57.5	COLOR VIDEO CAMERA
7.5		TRIPOD
		BASE

33 1/4-20UNC

MOUNTING HOLE

40 Design and specifications are subject to change without notice. 41