Mounting the camera

Note Read before starting work.•Special skills are required to install this unit.

•If you install the camera on a rainy day, be sure that rainwater does not get inside the camera.

•The camera’s mass is approx. 2.3 kg (including the mounting bracket). Take care to avoid dropping the camera during installation.

•Hold the camera by the stay cover while performing installation work.

•When you mount the camera body to the ceiling, be sure to wear safety goggles to protect your eyes from falling objects.

Create a hole in the ceiling

When mounting the camera to a wall, follow these instructions while replacing “ceiling” with “wall”.

Note

•Verify the strength of the ceiling. Insufficient strength may cause the camera to fall. If ceiling strength is insufficient, make sure to increase the strength before installation.

 

Anchor

 

170

 

bolt

 

 

 

2

 

 

 

1

48.5

28

3

93.5

50

 

 

1Create a hole in the ceiling (approx. Φ 28 mm).2Set up the anchor bolts on the ceiling.

Set up 4 anchor bolts (M8 x 35 mm or greater) on the ceiling to attach the mounting bracket (supplied) of the camera.

3Pull out the cables from the hole in the ceiling.

Removing the Front Cover

Remove the front cover to configure the switches.

Front cover

2

1

1Rotate the front cover counterclockwise.2Remove the front cover in the direction of the lens.
Attach the camera to the mounting bracket
Mounting the camera on the ceiling without the mounting bracket

Internal thread anchor

1

2

4

 

Solder or crimping

 

Wrap with insulation

 

tape

Audio/

5 Wrap with waterproof tape

3 Fall prevention wire

Alarm cable

LAN cable

Power cable

 

6

Stay

cover

Washer

Spring washer

Bolt (M8×20 mm or greater)

Mounting bracket
Sunshade

Stay cover

1Create a hole (approx. Φ 28 mm) in the ceiling, and pull the cables out from the ceiling.

2Insert 2 internal thread anchors (M8) for mounting the camera.3Connect the camera to the ceiling, and attach the fall prevention wire.

Note

•Attach the fall prevention wire coming out of the camera to a location of sufficient strength, such as a ceiling slab, etc.

•Take note of the length and strength of the fall prevention wire. Use wire made of insulated material. Make the wire length as short as possible.

4Connect the cables. (☞ [Cabling])5Wrap the cables with waterproof tape.6Mounting the camera.Tighten the bolts (M8 x 20 mm or greater) with the cables through the ceiling.

Note

•The provided bolts are for use with the mounting bracket only. Do not use the provided bolts for mounting the camera.

•Use stainless bolts, washers and spring washers. If you use steel parts, apply rust-proofing, for example, by painting them after installation.

When mounting the camera with cables pulled out from the side

When directly mounting the camera to a ceiling or wall, you can pull cables out from the side and avoid creating a hole for them. The method for mounting the camera is the same as [Mounting the camera on the ceiling without the mounting bracket].

1Hole for pulling out cables

2

1Cut the hole for pulling out cables using a nipper,and then break it off using needle-nose pliers.Create an opening on the side from which you will pull out the cables.2Pull out the cables.

3Perform steps 2 to 6 in [Mounting the camera on the ceiling without the mounting bracket].

When mounting the camera using an electrical boxFor details, contact the dealer from which you purchased this camera.

2

Fall prevention wire

1

3

Bolt (M8) (supplied)

Spring washer (supplied)

Washer (supplied)

Stay cover

Coaxial cable/ alarm cable

Mounting bracket (supplied)

Cabling

Connect the AC 24 V power cable, alarm cable, and audio cable to their respective connectors by crimping them or soldering them.

Wrap unused connectors and the ends of unused cables with insulation tape and waterproof tape.

Make sure the LAN cable is completely inserted into the connector. After confirming the connection, wrap it with waterproof tape.

Note

•If you use both the AC 24 V power cable and the PoE-based LAN cable simultaneously, the camera may fail. Always supply power using either method.

Cable extracting space *This diagram depicts mounting the camera to the ceiling.

1Pass the cable from the camera through the hole of the mounting bracket.2Pull out the fall prevention wire from the center hole of the stay cover.3Attach the camera to the mounting bracket with 2

Mounting the camera on the ceiling

Use nuts, washers and spring washers to attach the camera to the anchor bolts. Also attach the fall prevention wire when mounting the camera.

bolts (M8).Tighten the bolts with the supplied wrench.
When you mount the camera on the ceiling

Turn the camera so that the camera lens faces the cable extracting space, and attach the camera to the mounting bracket.

When you mount the camera on the wall

Solder or crimping

Wrap with insulation tape

Anchor bolt

Turn the camera so that the camera lens faces opposite the cable extracting space, and attach the camera to the mounting bracket.

Memo

•When mounting the camera to a wall, the direction of the camera when you attach it is different from when you attach the camera to the ceiling. To protect against water penetration, mount the camera so that the cable extracting space is facing downward.

Wall

Cable extracting space

Note

•Be sure not to pinch the fall prevention wire when attaching the camera to the mounting bracket. Gather all the cables in the indentation of the stay cover.

LAN

Power cable

cable

 

Audio/

Alarm cable

Fall prevention wire

Washer

Spring washer

Nut

Note

•Use stainless nuts, washers and spring washers. If you use steel parts, apply rust-proofing, for example, by painting them after installation.

☞ Continue to next page 2