How to attach the grip

1

2 3

Fit them to attachment holes.

Align them.

Usage precautions

1Never use any of the following chemicals for cleaning, rust- proofing, fog prevention, repair, or other purposes.

1)Do not clean the marine case with alcohol, gasoline, paint thinner, or other volatile organic solvents, chemical cleaners or similar agents. (Pure water or lukewarm water is adequate for cleaning.)

2)Do not use rust-proofing agents or the like on metal parts. (Stainless steel and aluminum are used for all metal parts, so pure water is adequate for cleaning.)

3)Do not use commercially-available anti-fogging agents. (Always use the fogging agent that came with the marine case.)

4)Do not use any silicon grease other than that specified for the O-ring. (Always use the silicon grease that came with the marine case.)

5)Do not use any adhesives for repairs, etc. (If any repairs are necessary, please consult the store of purchase.)

Direct or indirect use (vaporized chemicals) of any of the above chemicals on the marine case can cause cracks when the marine case is placed under high pressure.

2Exercise caution, as this marine case is a completely airtight structure. If it is left exposed to direct sunlight, or in a car, ship, or on the beach, the internal temperature can climb extremely high, which may cause the camcorder inside to stop working properly.

3Do not use the glass cleaner or cleaner for any purpose other than cleaning the front glass.

4If the camcorder is sealed inside the marine case in an area where the humidity and temperature are high, diving will make the humidity trapped inside the marine case cool down, causing condensation to form and the glass surface to become fogged. It is recommended that you insert the camcorder into the marine case in an area where the humidity is low and the temperature is close to that of the water where you will be diving.

If a piece of aluminum foil is cut to approx. 50 cm2 and is inserted into the glass part of the marine case, fog inside the marine case will adhere to the aluminum foil, as its heat conductivity is higher than that of glass. This is an effective way to quickly reduce fog inside the marine case.

5Do not open or close the case in areas where it may be subjected to water spray or sand.

6If you must open the marine case at the diving site in order to replace the battery or tape, observe the precautions below.

1)Select a location safe from water spray and sand.

2)Completely wipe off any water between the main unit and the lid section of the main case and on the buckles. Thor- oughly dry off any water remaining on the marine case with a dry cloth.

3)When removing the buckles and opening the lid section, be careful that no water drips from your hair or body into the marine case.

4)In order to avoid touching the camcorder with hands that have salt water on them, place a towel dampened with pure water in a plastic bag beforehand and use it to wipe any salt off your hands and fingers before touching the camcorder.

EN

7Do not throw the marine case into the water.

8After use, wash off adequately with pure water as soon as possible. If the marine case has been used in salt water, soaking the marine case in pure water for a while is an effective way to remove salt.

Be sure to operate all levers and buttons to wash off any salt in the grooves. If any salt remains, it will dry out and crystallize. This could result in water leakage.

9After washing, wipe off any water with a dry cloth free of salt to completely dry off the marine case. However, do not expose the marine case to direct sunlight in order to dry it. This can cause discoloration and breakage of the marine case, and can speed up deterioration of the O-ring.

0Wipe the inside of the marine case with just a dry cloth. Maintain the transparency of the front glass by wiping the inside face with a silicon cloth or the like moistened with cleaner agent.

!If the front glass is left dirty, it may cause fogging.

@Remove the O-ring from the lid section and wipe off any salt, sand, and other foreign matter. In the same manner, wipe off any adhering foreign matter from the groove into which the O-ring was fit and from the main unit of the marine case where the O-ring contacted it. When removing the O-ring from the groove, avoid using sharp-tipped metal objects; instead use a round-tipped object, such as a hair pin, to avoid damaging the O-ring when you remove it.

#Since the marine case is made of polycarbonate resin, handle it carefully. In particular, it can be easily scratched by rocks, etc. at the shooting site and may be damaged if it is dropped or otherwise subject to shock. When going to the shooting site by car, ship, train, or plane, avoid transporting the camcorder in the marine case. If you take adequate handling precautions, however, there should be no problem in transporting the camcorder in the marine case for a short distance, for example from the target site to the diving site.

$Avoid removing any parts other than those indicated in the

user’s manual, altering the marine case, or using any parts other than those specified. If any problems occur, please consult the store of purchase.

%The appearance and specifications of this unit are subject to change without prior notice.

Main specifications

Maximum pressure

: Water depth up to 30 meters

Power switch

: ON/OFF

Recording start/stop

: START/STOP

Snapshot

: SNAPSHOT

Zoom

: T/W

Main unit dimensions

 

(W x H x D)

: 170 mm x 150 mm x 140 mm

Main unit weight

: 0.7 kg

Compatible model

: GR-DVM55, GR-DVM75,

 

GR-DVX44, GR-DVX48,

 

GR-DVX49, GR-DVX77,

 

GR-DVX78, GR-DVX88

Accessories

: Maintenance kit (glass cleaner

 

agent (for anti-fogging), cleaner

 

agent (for removing dirt),

 

silicon grease, silicon cloth,

 

anti-fogging silica gel, paper,

 

cotton swabs, O-ring, strap,

 

grip)