Using Your Kambrook Jaguar
‘Power Twister’ Bagless
Vacuum Cleaner
Remove all packaging from the unit, hose and other accessories; ensure that you have removed all of the accessories before discarding the packaging.
Ensure that the dust canister and filters are correctly fitted.
Locate the crush proof hose and push the connection point into the hose inlet connection on the top of the unit, until a “click” sound is heard.
To extend the telescopic wand, push the extension lever in the direction of the arrow (printed on the lever) and pull out the narrower tube to the desired height.
Connect the wide end of the telescopic tube on to the hose end, and push together firmly.
Fit the floor head to the narrow end of the wand and push together firmly
Fully extend the power cord by pulling the power plug (situated at the rear of the unit) out from the unit, until the yellow tape on the cord is shown.
ENSURE THAT YOU DO NOT OVER EXTEND THE POWER CORD – DO NOT EXTEND PAST THE RED WARNING TAPE ON THE CORD
Plug into a 230/240v power point and switch the power on.
To commence vacuuming push down on the on/off foot pedal, at the top, rear of the unit. 
For full suction power ensure that the fingertip suction control cover (on the top of the hose) is closed.The suction power can be reduced by opening the suction control cover.
When vacuuming is complete, turn the vacuum cleaner ‘OFF’ by pushing down on the ‘ON/OFF’ foot pedal.Turn the power off at the outlet and then remove the power cord from the power outlet (when removing plug from the power outlet grasp the plug not the cord).
To retract the cord push down on the ‘cord rewind’ foot pedal. 
IMPORTANT: HOLD THE PLUG END WHEN RETRACTING THE CORD TO PREVENT IT FROM STRIKING YOU OR THE VACUUM.
ALWAYS ENSURE THAT THE DUST CANISTER IS CORRECTLY FITTED. NEVER OPERATE WITHOUT THE DUST CANISTER IN PLACE.
Crevice and brush tool accessories
The crevice tool is ideal for vacuuming hard to reach places such as the edges along skirting boards, crevices, corners and in between cushions.
The upholstery tool can be used to vacuum delicate surfaces and areas such as shelves, venetian blinds , furniture and lamp shades.
When using the crevice and upholstery tools, slide the Fingertip Suction Control cover (located on the wand handle) to the open position to reduce suction.
Both the Crevice and Uupholstery tools
can be stored on the telescopic wand tool storage stand for easy access and storage.
Turn the vacuum cleaner OFF when changing any attachments.
Park Tool Feature
The park tool feature can be used to park the wand in the upright (storage) position
The park tool attachment hook, for upright storage is located on the lower wand.
With the vacuum switched off and unplugged from the power point, insert the park tool hook into the park tool receptacle on the vacuum body
Note:The floor tool should be attached and in
contact with the floor to give stability, if correctly
assembled.
Emptying the Dust Canister
The dust canister should be emptied when the dust inside the canister reaches the max marking (indicated on the side of the canister).
Always switch the appliance off, then switch off at the power outlet and unplug the appliance prior to emptying the dust canister or changing filters.
To remove the dust canister, press the ‘dust canister compartment release button’ located on the side of the unit. The canister will then slide out.
NOTE:The canister compartment lid may not close
if the canister is not correctly fitted.
IMPORTANT: DO NOT USE THE UNIT WITHOUT THE DUST CANISTER IN PLACE
Replacing / Cleaning filters
HEPA and Micro Dust Filter
There are 2 dust filters located inside the dust canister.The outer filter is the Micro Dust filter and the inner filter is the HEPA filter.
To remove these filters for cleaning, follow the instructions listed under ‘Emptying the dust canister’ on page 5.
Once the dust canister lid has been removed, hold the top of the lid with one hand and grasp the bottom of the filter with the other hand to separate the filters from the dust canister
lid.You may need to rotate the bottom of the filter slightly clockwise to release.
The HEPA filter and Micro dust filter can be washed in lukewarm water. Allow to dry completely before placing the filters back into the dust canister.
To reposition the HEPA filter and Micro- filter follow these steps:
1.Hold the base of the HEPA filter
2.Slide the
3.Still holding the base of the filter in one hand, take the dust canister lid in the other hand and push the filter onto the lid so that the round opening in the filter fits over the round opening in the dust canister lid.
4 | 5 |
