Using Your Kambrook Jaguar Vacuum Cleaner
Remove all packaging from the unit, hose and other accessories; ensure that you have removed all of the accessories before discarding the packaging.
Ensure that the dust bag and filters are correctly fitted.
Locate the crush proof hose and push the connection point into the hose inlet connection on the top of the unit, until a “click” sound is heard.
Connect the wide end of the metal wand to the hose end, and push together firmly.
Fit the floor tool to the narrow end of the wand/s and push together firmly.
Fully extend the power cord by pulling the power plug (situated at the rear of the unit) out from the unit, until the yellow tape on the cord is shown.
ENSURE THAT YOU DO NOT OVER EXTEND THE POWER CORD – DO NOT EXTEND PAST THE RED WARNING TAPE ON THE CORD
Plug into a 230/240v power point and switch the power on.
To commence vacuuming push down on the on/off foot pedal, at the top, rear of the unit. 
When vacuuming is complete, push down on the ‘on/off’ pedal to switch off.Turn the power off at the outlet and then remove the power cord from the power outlet (when removing plug from the power outlet grasp the plug not the cord).
To retract the cord push down on the ‘cord rewind’ pedal. 
IMPORTANT: HOLD THE PLUG END WHEN RETRACTING THE CORD TO PREVENT IT FROM STRIKING YOU OR THE VACUUM.
ALWAYS ENSURE THAT THE DUST BAG AND THE MOTOR PROTECTION FILTER ARE CORRECTLY FITTED. NEVER OPERATE WITHOUT THE DUST BAG AND FILTERS IN PLACE.
Variable Power Control
The variable power control slide switch is located on the top of the vacuum cleaner. Slide the control to the rear for maximum power for vacuuming hard floor and carpet surfaces. Slide the control to the front at the minimum power level when using the crevice and brush tools.
Crevice and brush tool accessories The crevice tool is ideal for vacuuming
hard to reach places such as the edges along skirting boards.
The brush tools can be used to vacuum delicate surfaces and areas such as shelves and venetian blinds.
Set the variable speed control between minimum and medium power when using the tool accessories.
Turn off the vacuum cleaner when changing any attachments.
Dust bag indicator and changing the dust bag
You have the option of using a Cloth bag or a paper dust bag.
The dust bag should be changed when full.
The dust bag indicator window will gradually turn red as the bag fills up and when the dust bag indicator displays ‘red’ it is time to change the dust bag.
Always switch appliance off, then switch off at the power outlet and unplug the appliance prior to replacing dust bags or filters.
To remove the dust bag, ensure the unit is down on its wheels, remove the crush proof hose and push the ‘Dust bag compartment lid release lever’ underneath the handle. Once the lid has released, pull the top cover back.
To remove the bag, grasp the top of dust bag and pull out. If you are using the cloth bag dispose the dust in a rubbish bin. If you are using a paper dust bag you can dispose the bag with its contents in the rubbish bin.
To place a new dust bag, take a fresh dust bag and with the arrow (printed on the material section of the dust bag) pointing down slide the material down into the dust bag holder, until it comes in contact with the bottom of the holder.
Filter holder
Dust bag holder
HINT: once the bag is inserted
When vacuuming fine dust particles, the fine dust particles can clog the pores of the dust bag and the dust bag indicator will indicate full. If this happens the bag could appear relatively empty, however the bag will still need to be changed to avoid strain on the motor.
NOTE:The bag compartment lid may not close if
the bag is not correctly fitted.
IMPORTANT: DO NOT USE THE UNIT WITHOUT A DUST BAG IN PLACE
Replacing filters
Filters must be cleaned from time to time to remove the fine dust particles that have been collected.This can be done by shaking them; however after approximately 5 dustbag changes the filters should be replaced.
Motor protection filter
The motor protection filter must always be in place when operating the vacuum otherwise damage to the motor may occur
To replace the motor protection filter – Remove the dustbag or pull the bag forward.The motor protection filter is located at the rear, right hand side of this inner chamber. Pull the plastic filter holder upward to remove.
Filter holder
Removable filter
4 | 5 |
