Kenmore 625.38825 Faceplate Timer Features, Extra Recharge, Salt Monitor System, Recharge Tonight

[i:ii:ii:ii:_i:i:ii:_I SECTION 2 I_i:ii:ii:ii:_i:i:ii:_] HOW YOUR WATER SOFTENER WORKS

A. FACEPLATE TIMER FEATURES

S	EXTRA		RECHARGE
	Sometimes,		a	manually	started
	regeneration		(recharge)		may	be
C	desired, or needed. Two exam-
	ples are:
	- You	have	used	more	water	than
T	usual	(guests		visiting)	and	you

may run out of soft water before

the next timer started regenera- tion.

-You did not refill the softener

		with salt before it was gone. After
N		you	refill	with	salt:
		You	can	start	a regeneration		right
		away, or you can set the timer to
,JJJJJJJJJJJJJJJJ.		regenerate		at the next 2:00 AM (or
,JJJJ	JJJJJJJJJJ.
,JJ	JJJJJJJJJ.	other	preset		recharge	time).	Do
,JJJ	JJJJJJJJJ.	the following.
,JJ	JJJJJJJJJ.
'dJ_idJdJdJdJ"

,JJJJJJJJJJJJJJJJ.

,JJJJJJJJJJJJJJJJ.

RECHARGE NOW		i°'I _	3,n_q	_
		_"	I'U!_-I
Press the ON/OFF-HOLD	but-	i/	._C.A.G_
ton and hold until *RECHARGE

Serv and Fill begin to flash in the display. Upon

reaching fill the first cycle of regeneration, the flash-

ing Serv goes off and Fill is on steady. RECHARGE

continues to flash. This regeneration will last for about 2 hours. After the 2 hours, you will have soft water again.

*Note:

If the CLEAN feature is set to ON, a cleaning back- wash (CLEAN and Bkwsh or Rinse flashes in the dis-

play, along with the minutes of the clean cycle re-

maining) precedes the recharge.

SALT MONITOR SYSTEM

The face plate timer has a low salt monitor with an

indicator light to remind you to refill the storage tank with salt. To set this monitor system:

_1_ Lift the salt hole cover and level the salt in the storage tank.

ffi The salt level decal on the brinewell inside the

tank, has numbers from 0 to 8 (see drawing be- low). Observe the number the leveled salt is at or closest to.

m Now, press the SALT LEVEL ADJUST button until black bars display up to the salt level num-

ber. For example, the pictures below show the salt level at 6.

!!Finall3_ set the level you want the low salt indi- cator light to come on. Press the SIGNAL LIGHT

ADJUST button until a (_) shows opposite this

number. In the example below, the light will come on when the stored salt drops to level 2. At level 2, the storage tank is about 1/3 full. This is the lowest you should allow the stored salt level to drop to (see note on page 1-6).

_'_ If you wish to turn the salt monitor off, press the

SIGNAL LIGHT ADJUST button until OFF shows above.

Note:

For accurate salt monitor operation, always use

nugget or pellet water softener salt. See page 1- 6.

bars, salt level

RECHARGE TONIGHT [ !°_ _:l-_n _-

Press and release (do not hold) the I i R_C._G_TO_G.,

ON / OFF-HOLD button. RE-

CHARGE TONIGHT flashes in the display, and the

softener begins regeneration at the next preset re- charge time. Press and release the ON/OFF-HOLD button once more if you deride to cancel the regen-

eration, and RECHARGE TONIGHT.

brinewell

	8	,
		decal
salt
level	7	,

TONIGHT

6RECHARGE NOW

indicator light s°w

2-1