Kentrox Q2300 manual Specifications, Interfaces

SPECIFICATIONS

INTERFACES
WAN:	One 10/100Base-Tx (RJ45)
LAN:	Four-port, 10/100 Ethernet switch (RJ45)
	auto-sensing, auto-polarity
Control port (CLI):	One RS-232 (RJ45)
Modem (optional):	One V.92 modem (RJ11C) for dial-in management
MANAGEMENT/ADMINISTRATION
GUI:	Intuitive Web-style GUI (accessible from WAN
	or LAN)
Access Management:	Three levels—admin, configure, view;
	up to 10 users with passwords
Logs:	Alarm, System, Intrusion, Traffic, VPN
	Syslog support
SNMP:	Traps, MIB II, I/F MIBs
Updates:	Software updates via FTP or GUI
CLI:	Intuitive command line interface (CLI) accessible
	via control port, Telnet, SSH, or modem
Real-time Clock:	SNTP support and 8-hour power failure backup
FIREWALL
Protection Methods:	Stateful Packet Inspection designed for ICSA
	compliance
	Denial of Service (DoS)
	Intrusion Detection System (IDS)
	Blacklist
	TCP and UDP packet filtering
	NAT
	Application Layer Gateways (ALG)
Policies:	50 user-configurable policies
Mapped IP:	16 mapped IP (virtual DMZ/port forwarding)
Zones:	Trusted, Untrusted, DMZ
VIRTUAL PRIVATE NETWORK (VPN)
IPSec:	100 IPSec VPN tunnels
	Internet Key Exchange (IKE)
	Main and aggressive modes
	Diffie-Hellman MODP groups 1, 2, and 5
	Perfect Forward Secrecy (PFS)
	IPSec NAT traversal
Authentication:	Pre-shared key
	X.509 certificates
Encryption:	DES, 3DES, AES (128 bit), hardware acceleration
	for DES/3DES
Hash algorithms:	MD5 and SHA-1
WAN PROTOCOLS
Protocols:	IP or PPPoE

ROUTER
Routing:	Static, RIP v1/v2, and OSPF
	DHCP server, client, relay
	DNS client, DNS relay
	VLAN support for 8 LAN subnets
	Load balanced on 4 equal cost routes
QUALITY OF SERVICE
Bandwidth	Class-based Weighted Fair Queuing
Management:	Auto DiffServ/ToS-based priority queuing
	VoIP and video prioritization
	All DiffServ classes supported
	Configurable queue weighting
Marking:	Configurable QoS marking
Policies:	32 user-configurable QoS policies for prioritization
	by source and destination addresses, port,
	protocol, DiffServ Code Point (DSCP)
Monitoring:	QoS traffic reports and graphs
	Configurable WAN Latency report
Standards:	Supports 802.1P user priority and
	VLAN 802.1Q tags
DIAGNOSTIC LEDS (FRONT PANEL)
System:	System status, security alert, modem status
WAN:	Port status, Tx status, Rx status
LAN:	Port status, Tx status, Rx status
PHYSICAL
Dimensions:	1.6" H x 11.8" W x 8.6" D
	(44mm H x 300mm W x 219mm D)
Weight:	3.8 lbs. (1.72 kg)
Power:	Universal AC adapter, 100-240 VAC input,
	50-60 Hz; power consumption: ≤ 20W
Mounting Options:	Table-top, wall-mount or optional
	19" rack-mount (1RU)
ENVIRONMENT
Operating:	0° to 50°C (32° to 122°F)
	5% to 95% RH (non-condensing)
Storage:	-20° to 66°C (-4° to 150°F)
	5% to 95% RH (non-condensing)
REGULATORY
Emissions:	FCC 47 CFR 15 Class A
Safety:	ANSI/UL 60950-1-2002
	CAN/CSA-C22.2 No 60950-1-03
Terminal:	FCC 47 CFR 68
	IC CS-03

05-15-002-3 3/06 Copyright © 2006 by Kentrox, LLC. All Rights Reserved. Kentrox is a registered trademark and Q-Series is a trademark of Kentrox, LLC. Information published here is current as of this document’s date of publication, but is subject to change without notice. You may verify product information by contacting our headquarters in Hillsboro. Kentrox is an Equal Employment Opportunity/Affirmative Action employer.

Kentrox, LLC

20010 NW Tanasbourne Dr. Hillsboro, OR 97124 Phone 503-643-1681

Service and Support 800-733-5511 www.kentrox.com