Kenwood C-V301, C-V351 8 9;) ) MHz, Receiving a preset station, Storing radio stations manually in preset memory, Receiving all preset stations in order (P. CALL), Preparation, GRC

The AUTO MEMORY function gives precedence to RDS stations and assigns them from preset number 1. Therefore, when it is required to preset RDS stations as well as non-RDS stations, execute the AUTO MEMORY operation first then proceed to the manual memory operation of non-RDS sta- tions.

Preparation

÷ Select the TUNER input. &

÷Display the Tuner operation menu. &

RDS (Radio Data System)

C-V351/C-V301 (EN)

Order of radio station presetting				29
	Other stations than the RDS stations can be stored in
	the preset memory by presetting them after the RDS
	stations preset by AUTO MEMORY as shown below or
	overwriting the RDS stations preset in some preset
	numbers.
	Preset number
	1 2		39 40
	1 AUTO MEMORY	~	2Manual memory
	RDS stations		FM stations
	(~ FM stations)		or LW or MW stations

Storing radio stations manually in preset memory

RC GRC

1Select the receiving band.2 Select a station or frequency.3 Press the Memory key during receiving a station.

MEMO	Memory /
AUTO
	10key Pad
MEMORY
Proceed to step 4	ENTER
within 10 sec.	Memory
(If more than 10 sec.
have elapsed, press the	ENTER
Memory key again.)

4Select one of the preset numbers from 1 to 40.

				PTY SEARCH	1 2		3
				+10	4	5	6
1	2	3	4	5	7	8	9
6	7	8	9	0	0	+10

ENTER

÷Apart from the auto memory function, RDS stations can also be stored manually in the preset memory.

÷In the manual memory storage operation of radio stations, it may take a few minutes after the Memory key is pressed till the memory display starts to blink depending on the receiving condition.

Lights up (for 10 sec.) Blinks (for 10 sec.)

FM ) -	8 9;) ) MHz
MEMO

Press the numeric keys in the following order:... (RC) To store in “15” ....... 0, 5

Press the numeric keys in the following order:... (GRC) To store in “15” ....... 0 ENTER 5 ENTER

÷Repeat steps 1,2,3,4 for each of the stations to be stored in memory.

÷If a station is stored in a preset number which has already stored a station memory under it, the previous memory is replaced by the new memory content.

÷If RDS stations are stored manually in the preset memory, the PS may not be included in the memory depending on receiving conditions.

Receiving a preset station

RC

Enter the preset number (max. 40) of the desired station.

				PTY SEARCH
				+10
1	2	3	4	5
6	7	8	9	0

GRC

Memory /

10key Pad

ENTER

1 2 3

4 5 6

7 8 9

0 +10

Press the numeric keys in the following order:...(RC) To recall “15” ........... 0, 5

Press the numeric keys in the following order:...(GRC) To recall “15” ........... 0 ENTER 5 ENTER

÷If you make a mistake in entering the figure of 10, press the 0key repeatedly until the original display is shown, then enter the correct number.

Preset number stored in memory

ENTER

Receiving all preset stations in order (P. CALL)

RC		GRC
The preset	The preset
number	number	The preset number	The preset number
decreases.	increases.	decreases.	increases.
P.CALL
fi %		P.Call
PTY	TA/NEWS/INFO.
		01ch

ENTER

÷Every time the key is pressed, the next station in the order of the preset number is received.

When you press P.Call key, .......................

1	2	3	38	39	40
When you press P.Call key, ......................
1	2	3	38	39	40

If the key is held pressed ..............	Preset stations will be received suc-
	cessivelyforabouthalfasecondeach.