5. When the display shows the correct
hour and minute, press the ENTER
button to turn the alarm on.
6. Press the MEMO button to save your
settings. The Step 2—Set Stream
screen will appear (right).
7. Use the CH/PRESET jog dial (unit) or press the CH buttons (remote) to move through
the streams until the one you want is highlighted. (The stream will play.)
8. Press the ENTER button to save your setting. The Alarm Setup screen will reappear.
Press the SETUP button to exit the Setup Mode.
Using the alarm
At the specified time (see Setting The Alarm), the DT-7000S will automatically turn itself
on to the selected stream.
• The selected stream will play and the time display will flash positive and negative.
Note: To hear the DT-7000S, make sure that the audio system it is connected to is
turned on.
To enter the “Snooze” mode, press any button once.
• The Snooze cycle is 10 minutes long.
• You can repeat the Snooze cycle as many times as you want.
To shut the alarm off, press any button twice. (This shuts the DT-7000S completely off.)
To continue listening to SIRIUS after you’ve shut the alarm off, press the POWER button.
Auto Shutoff
You can set DT-7000S to automatically shut off if it is accidentally left on (if a button
isn’t pressed for 15, 30 or 60 minutes).
1. While in the Setup Mode, turn the CATEGORY jog dial (unit) or press the CAT buttons
(remote) until the Auto Shutoff Setup
screen appears (right).
2. Turn the CH/PRESET jog dial (unit)
or press the CH buttons (remote)
until the display shows amount of
time you want DT-7000S to stay on
after the last time a button is
pressed before it automatically
shuts off. Press the SETUP button to exit.
• When Auto Shutoff is activated, the screen will display a countdown warning 10
seconds before the DT-7000S shuts itself off. Pressing any button during this
countdown will cancel the Auto Shutoff process and restore normal operation.
Sleep Timer
You can program the DT-7000S to play for 30 or 60 minutes and then automatically turn
itself off.
1. While listening to SIRIUS, press the ENTER button to enter the Stream List mode.
2. Then hold the ENTER button for at
least 1 second. The Timer Setup
screen will appear (right).
3. Use the CH./PRESET jog dial (unit) or
the CH buttons (remote) to highlight
the amount of time you want the
DT-7000S to play before it shuts off.
4. Press the ENTER button to confirm your selection and activate the Sleep Timer.
When the Sleep Timer is active, the display will return to the Normal Operation screen.
• The display will appear as normal except that every three seconds the timer
countdown will replace the stream number. You can still change streams and display
modes as normal without shutting the timer off.
To cancel the Sleep Timer, turn the DT-7000S’s power off, then turn it back on again.
Note: You must re-set the Sleep Timer each time you want to use it.
Channel Skip/Lock
This allows you to select streams that you want to skip when scanning up and down the
Channel List and Category List screens, or simply when you’re pressing the cursor up &
down buttons.
1. While in the Setup Mode, turn the
CATEGORY jog dial (unit) or press the
CAT buttons (remote) until the Channel
Skip/Lock screen appears (right).
2. Use the CH/PRESET jog dial (unit) or
the CH buttons (remote) to highlight
the stream you want. (The highlighted stream will automatically play.)
3. Press the ENTER button to change the highlighted stream’s status from “available”
(+) to “skip” (–).
• To exit the Channel Skip function, turn the CATEGORY jog dial (unit) or press the CAT
buttons (remote). The screen will display the next Setup Menu item.
You can further lock a stream by placing it in the Channel Lock mode. Locked streams
will be unavailable during all tuning modes, and cannot be directly accessed via the
remote control.
To lock a stream, in Step 3 above, instead of momentarily pressing the ENTER button,
hold the button for more than 1 second. A “–” and a padlock will be displayed next to
the stream number.