safety

The blades and plates are very sharp, handle with care. Always hold the knife blade by the finger grip at the top, away from the cutting edge, both when handling and cleaning.

Always remove the knife blade before pouring contents from the bowl.

Keep hands and utensils out of the processor bowl and liquidiser jug whilst connected to the power supply.

Switch off and unplug:

before fitting or removing parts

after use

before cleaning

Never use your fingers to push food down the feed tube. Always us e the pusher supplied.

Before removing the lid from the bowl or liquidiser from the power unit:-

switch off;

wait until the attachment/blades have completely stopped;

Liquids should be allowed to cool to room temperature before blending.

This machine will be damaged and may cause injury if the interlock mechanism is subjected to excessive force.

To prevent damage to the interlock mechanism:-

Always lock the bowl to the power unit before attempting to fit the lid.

Always unlock the lid before attempting to remove the bowl from the power unit.

Never use an unauthorised attachment.

Never leave the machine on unattended.

Never use a damaged machine. Get it checked or repaired: see ‘service and customer care’.

Never let the power unit, cord or plug get wet.

Don’t let excess cord hang over the edge of a table or worktop or touch hot surfaces.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with t he appliance.

Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.

Misuse of your processor/liquidiser can result in injury. before plugging in

Make sure your electricity supply is the same as the one shown on th e underside of your appliance.

Important – UK only

The wires in the cord are coloured as follows: Blue = Neutral, Brown = Live.

The appliance must be protected by a 3A approved (BS1362) fuse.

Note:

For non-rewireable plugs the fuse cover MUST be refitted when replacing the fuse. If the fuse cover is lost then the plug must not be used until a replacement can be obtained. The correct fuse cover is identified by colour and a replacement may be obtained from your Kenwood Authorised Repairer (see Service).

If a non-rewireable plug is cut off it must be DESTROYED IMMEDIATELY. An electric shock hazard may arise if an unwanted non-rewireable plug is inadvertently inserted into a 13A socket outlet.

This appliance conforms to EC directive 2004/108/EC on Electromagnetic Compatibility and EC regulation no. 1935/2004 of 27/10/2004 on materials intended for contact with food.

before using for the first time

1Remove all packaging including the plastic blade covers from the kni fe blade. These covers should be discarded as they are to protect the blade d uring manufacture and transit only.

2Wash the parts: see ‘cleaning’.

3Wrap excess cord around the cord stowage at the back of the appl iance.

key

￿safety interlock

￿pusher

￿feed tube

￿lid

￿bowl

￿food processor drive

￿on/off/pulse lever

attachments

￿liquidiser

￿knife blade

￿shredding plate

￿slicing plate

￿plate carrier

￿spacer

￿whisk

￿maxi blend canopy

￿Citrus press is an optional accessory and may not be included in your pack.

to use the food processor

1Fit the bowl onto the processor base - handle towards the back - lower and turn clockwise until it locks firmly into place ￿.

2Add an attachment over the food processor drive.

Always fit the bowl and attachment onto the machine before adding ingredients.

3 Fit the lid onto the bowl - feed tube towards the back of the machine ￿. Turn

clockwise until the arrow on the lid aligns with the raised line on the body of the processor ￿.

Failure to correctly fit the lid will prevent your food processor from operating.

4Switch on by moving the on/off/pulse lever to ‘I’ and process until the desired consistency is achieved OR move the lever to the pulse ‘P’ position to operate the tool fitted to the bowl in a start/stop action. The pulse feature operates the motor and keeps it running for as long as it is held in position. This will allow you to control the texture of various foods eg when processing meat.

5Switch off and reverse the above procedure to remove the bowl, lid and attachments.

The lid can only be removed when the on/off/pulse lever is in the ‘0’ position.

important

Your processor is not suitable for crushing or grinding coffee beans, spices or converting granulated sugar to caster sugar.

When adding almond essence or flavouring to mixtures avoid contact with the plastic as this may result in permanent marking.

maximum capacities

 

egg whites

6

chopping meat

300g/10oz

shortcrust pastry flour weight

250g/9oz

yeast dough flour weight

340g/12oz

one stage sponge cake total weight

800g/1lb 12oz

soup with canopy

800ml/1.3pt

liquidiser

1 litre/134 pts.

using the attachments

knife blade

This blade is the most versatile of all the attachments. The texture you get is determined by the length of processing time. For coarser textures use the ‘pulse’ feature checking the consistency regularly.

what the knife blade can do.

Raw meat

Make ‘mince’ by trimming raw meat of any excess fat and cutting into 2cm/34in cubes, place into the bowl and operate for approximately 10 seconds or until the desired texture is achieved. The longer you run the machine the smoother the texture will be.

2

Page 3
Image 3
Kenwood FP180 manual Safety, Key, Attachments, To use the food processor, Using the attachments