Kenwood KAC-7202, KAC-7252 Troubleshooting Guide, Specifications

English 7
Troubleshooting Guide
What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following
table for possible problems.
PROBLEM POSSIBLE CAUSE SOLUTION
No sound.
(No sound from one side.)
(Blown fuse.)
• Input (or output) cables are disconnected.
• Protection circuit may be activated.
• Volume is too high.
• The speaker cord is shorted.
• Connect the input (or output) cables.
• Check connections by referring to <Protection function>.
• Replace the fuse and use lower volume.
• After check the speaker cord and fixing the cause of the short,
replace the fuse.
The output level is too small
(or too large).
• The input sensitivity adjusting control is not set to the correct
position.
• Adjust the control correctly referring to <Controls>.
The sound quality is bad.
(The sound is distorted.)
• The speakers wire are connected with wrong + /-polarity.
• A speaker wire is pinched by a screw in the car body.
• The switches may be set improperly.
• Connect them properly checking the + / - of the terminals
and wires well.
• Connect the speaker wire again so that it is not pinched by
anything.
• Set switches properly by referring to <System examples>.
The Remote Controller does
not function.
• The Remote Cable is disconnected.
• The "BOOST LEVEL" is set to "0dB".
• Connect the Remote Cable securely and correctly.
• Adjust the "BOOST LEVEL".
Specifications
Specifications subject to change without notice.
Audio Section ........................................................................................................................KAC-7252 KAC-7202
Max Power Output ......................................................................................................................................................................................1000 W 920 W
Rated Power Output (+B = 14.4 V)
Normal (4 Ω) (20 Hz – 20 kHz, 0.08 % THD) ..............................................................................................................170 W × 2 150 W × 2
Normal (4 Ω) (DIN : 45324 , +B = 14.4V) .....................................................................................................................170 W × 2 150 W × 2
Normal (2 Ω) (1 kHz, 0.8 % THD) .....................................................................................................................................250 W × 2 230 W × 2
Bridged (4 Ω) (1 kHz, 0.8 % THD) ....................................................................................................................................500 W × 1 460 W × 1
Sensitivity (rated output) (MAX.) ..............................................................................................................................................................0.2 V 0.2 V
Sensitivity (rated output) (MIN.) ...............................................................................................................................................................5.0 V 5.0 V
Input Impedance ............................................................................................................................................................................................ 10 kΩ 10 kΩ
Frequency Response (+0, –3 dB) ...........................................................................................................................................5 Hz – 50 kHz 5 Hz – 50 kHz
Signal to Noise Ratio ................................................................................................................................................................................≤100 dB ≤100 dB
Low Pass Filter Frequency (24 dB/oct.) .............................................................................................................50 – 200 Hz (variable) 50 – 200 Hz (variable)
High Pass Filter Frequency (12 dB/oct.) ............................................................................................................50 – 200 Hz (variable) 50 – 200 Hz (variable)
Bass Boost Circuit ............................................................................................................................................................0 – +18 dB (variable) 0 – +18 dB (variable)
Bass Boost Frequency .................................................................................................................................................40 – 100 Hz (variable) 40 Hz
General ..................................................................................................................................KAC-7252 KAC-7202
Operating Voltage ........................................................................................................................................... 14.4 V (11 – 16 V allowable) 14.4 V (11 – 16 V allowable)
Current Consumption .....................................................................................................................................................................................40 A 40 A
Installation Size (W × H × D) ..................................................................................................................................... 380 × 61 × 286 mm 380 × 61 × 286 mm
Weight ..................................................................................................................................................................................................................5.8 kg 5.7 kg