Connection
WARNING
Remove the ignition key and disconnect the negative ·terminal of the battery to prevent short circuits.
CENTER UNIT | RCA cable* |
(CD receiver, etc.) |
|
|
|
CAUTION
• If sound is not output normally, immediately |
turn power off and check connections. |
Hexagon Wrench (Small) 
Power control wire* | Use the |
| |
| attached |
| Hexagon |
| Wrench. |
NOTE
Use a RCA cable with a straight terminal. If a RCA cable with L type terminal is used, it may not be able to connect.
Left input
• Be sure to turn the power off before | ||
| changing the setting of any switch. | |
• | If the fuse blows, check wires for shorts, then | |
| replace the fuse with one of the same rating. | |
• Check that no unconnected wires or | ||
| connectors are touching the car body. Do | |
| not remove caps from unconnected wires or | |
| connectors to prevent short circuits. | |
• Connect the speaker wires to appropriate | ||
| speaker connectors separately. Sharing the | |
| negative wire of the speaker or grounding | |
| speaker wires to the metal body of the car | |
| can cause this unit to fail. | |
• | After installation, check that the brake | |
| lamps, winkers, and wipers work properly. | |
|
|
|
| * Commercially available parts |
|
WARNING
To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the battery’s positive terminal.
Hexagon Wrench | BATT. GND | LEFT | RIGHT | LEFT | RIGHT |
|
|
(Small) |
|
|
|
|
| L |
|
|
|
|
|
|
| R |
|
| FUSE [30Ax2] | BRIDGED |
| BRIDGED | A B | A + B | |
|
| SPEAKER OUTPUT A | SPEAKER OUTPUT B | LINE IN | LINE OUT | ||
Hexagon |
|
|
|
| A channel input | Right input | |
|
|
|
|
| |||
Wrench (Large) |
|
|
|
|
|
| |
| Use the |
|
|
|
|
| B channel input |
| attached |
|
|
|
|
|
|
| Hexagon |
|
|
|
|
|
|
| Wrench. |
|
|
|
|
|
|
Battery wire* |
|
|
|
|
| B channel | |
Protective Fuse* |
|
|
|
|
| Right speaker | |
|
|
|
|
|
| ||
|
|
|
|
|
|
| B channel |
|
|
|
|
|
|
| Left speaker |
| Terminal cover |
|
|
|
|
| A channel |
|
|
|
|
|
| Right speaker | |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| A channel |
|
|
|
|
|
|
| Left speaker |
Battery | Ground wire* |
|
|
|
| Bridged Connections | |
|
| LEFT | RIGHT | LEFT | RIGHT | ||
|
| BRIDGED |
| BRIDGED |
|
| B channel |
|
| SPEAKER OUTPUT A | SPEAKER OUTPUT B |
|
| ||
|
|
|
|
|
|
| Speaker (Bridged) |
|
|
|
|
|
|
| A channel |
|
|
|
|
|
|
| Speaker (Bridged) |
About the Lead Terminals
1. Wire Thicknesses
You can use wires with the following thicknesses:
Battery wire and ground wire | AWG 4 | – AWG 6 |
Speaker wire | AWG 8 | – AWG 12 |
2. Strip the wire
Make a cut in the wire sheath (insulator made from vinyl, etc.) at the position
3. Install the wire
Loosen the screw using the supplied hexagon wrench. Insert the conductor of the wire in the terminal hole, and then tighten the screw.
| Hexagon |
| |
10 - 13 mm | Wrench | Hexagon Wrench | |
(3/8" - 1/2") | (Large) | ||
(Small) | |||
|
|
English