Kenwood TS-2000

4 GETTING ACQUAINTED

FLOCK A

CH1/REC

CH2/REC

CH3/REC

TONE/SEL

METER

CTCSS/SEL

NB/LEVEL

AGC/OFF

FINE/STEP

DCS/SEL

SHIFT/OFFSET

ENT

SEND

PHONES

MIC

ANT1/2

PROC

LEVEL

VOX

ATT PRE

LEVEL

MANUAL

LO/

WIDTH HI/

SHIFT

N.R.

A.N.

B.C.

FUNC

CALL

C.IN

CLR

MAIN

AUTO

CAR

TX MONI

DELAY NAR

REV

MIC

PWR

KEY

LSB

USB

FSK

SUB

DISP

SEL

1MHz CTRL

MG.SEL

M.IN

QUICK MEMO

M/S REV

TRACE

MAIN

MANUAL RF

SQL

SUB

MULTI

BC MAIN

GAIN

VFO/CH

MENU TF-

SET

MAIN SUB

SG.SEL

SCAN M VFO M.IN

RIT

CW TUNE 9.6k STA

RIT/SUB

CON

XIT

ALT

SET

CLEAR

P.C.T

HF/VHF/UHF ALL MODE MULTI BANDER TS-2000

SATL

A/B

VFO/M

SPLIT

A=B

!4 Multi-purpose keypad

Consists of 10 keys that are used to enter numeric

data. Also used for the following functions:

•1/ CH1/REC, 2/ CH2/REC, and 3/ CH3/REC keys

Press to play back or record the CW or voice

messages that are associated with the DRU-3A

Digital Recording Unit {page 89} and the internal

electronic keyer {page 43}.

•4/ TONE/SEL key

Press to activate the sub-audible Tone function to

access repeaters for FM mode. To select the Tone

frequency, press [FUNC], [4/ TONE/SEL], then

select your desired tone frequency using the

MULTI/ CH control {page 33}.

•5/ METER key

Press to select the meter scales {page 19}.

•6/ CTCSS/SEL key

Press to activate the Continuous Tone Coded

Squelch System (CTCSS) function for FM mode.

To select the CTCSS tone frequency, press

[FUNC], [5/ CTCSS/SEL], then select your

desired CTCSS tone frequency using the

MULTI/ CH control {page 35}.

•7/ NB/LEVEL key

Press to switch the Noise Blanker ON or OFF.

Press [FUNC], [7/ NB/LEVEL] to adjust the Noise

Blanker level {page 57}.

•8/ AGC/OFF key

Press to adjust the response time of the Automatic

Gain Control. To switch the AGC OFF, press

[FUNC], [8/ AGC/OFF] {page 38}.

•9/ FINE/STEP key

Press to activate the Fine tuning function to allow

more precise tuning {page 38}.

••/ DCS/SEL key

Press to activate the Digital Coded Squelch

function for FM mode. To select the DCS code,

press [FUNC], [•/ DCS/SEL], then select your

desired code using the MULTI/ CH control

{page 36}.

•0/ SHIFT/OFFSET key

Press to switch the Shift function for FM mode ON

or OFF when accessing the repeaters. The Shift

frequency can be manually adjusted by pressing

[FUNC], [0/ SHIFT/OFFSET], then adjusting the

shift frequency value using the MULTI/ CH control

{page 32}.

•ENT key

Press to enter your desired frequency using the

keypad {page 37}.

!5 FUNC key

Press to access the secondary functions that are

assigned to the keys. While FUNC is active, the

FUNC LED lights orange.

!6 MIC/ CAR key

Press to adjust the microphone gain {page 20}.

While the Speech Processor function is ON, it

becomes the Speech Processor output level

adjustment key {page 40}.

Press [FUNC], [MIC/ CAR] to adjust the carrier level

for CW, FSK and AM mode {page 20}.

!7 PWR/ TX MONI key

Press to adjust the output power {page 20}. Press

[FUNC], [PWR/ TX MONI] to monitor your

transmission signal {page 79}.

!8 KEY/ DELAY key

Press to adjust the internal electronic keyer speed.

Press [FUNC], [KEY/ DELAY] to adjust the VOX

delay time or break-in time (Full break-in/ Semi

break-in time) for CW mode {page 42}.