2511 ADIRONDACK BENCH
Contents: | (18) 1/4 - 20 x 2” Bolts | ||
(1) | Seat, (1) Back | (2) | 1/4 - 20 x 2 1/2” Bolts |
(2) Arm Rests | (1) | #10 x 3” Screw | |
(2) | Front Chair legs | (10) Washers | |
(2) | Back Chair legs | (10) Locknuts | |
(2) | Cross Braces | Locknut Washer Bolt |
Tools Required:
#3 Phillips Head Screwdriver
7/16” Wrench
a. Align predrilled holes then insert bolts
1.to attach front legs.
b. Align predrilled holes then insert bolts to attach back legs.
1a. | 1b. |
Assembly Instructions
1. a. With the wing on the post facing front, |
align the predrilled holes on front leg to the seat |
and insert the 1/4 - 20 x 2” Bolts through the leg |
in thru the seat. Clean any plastic residue from |
the bolt then slide a washer on. Screw on the |
locknut and then tighten it with the wrench and |
phillips screwdriver. |
b. Align the predrilled holes on the back leg to |
the seat and insert the 1/4 - 20 x 2” Bolts through |
2. | Place arm rest |
| on top of chair |
| legs, align front |
| predrilled holes, |
| insert bolt. |
Attach the back
3.of the chair by aligning holes on the arm and the seat to insert bolt.
the leg in thru the seat. Clean any plastic residue |
from the bolt then slide a washer on. Screw on the |
locknut and then tighten it with the wrench and |
phillips screwdriver. Repeat on the other front leg. |
2. Place arm rest on top of chair legs align the |
front predrilled holes and insert the 1/4 - 20 x 2” |
Bolts through the leg and in thru the arm. Clean |
| 3b. | |
| 3a. | |
4. |
| |
Attach the | Slide washer then | |
braces to | ||
locknut onto end of | ||
the legs by | ||
bolt then tighten. | ||
aligning holes | ||
| ||
and inserting |
| |
a 2” bolt. |
|
5.Insert the bolt thru the center
seat brace into the center of the back of bench.
Properly Seated
Washer and Nut.
Copyright © Kettler USA 309.01
off any plastic residue then slide a washer on the | |
end of bolt. Screw on the locknut and then tighten | |
it with the wrench and phillips screwdriver. | |
3. | a. Attach the back of the chair to the seat |
| |
by aligning holes and inserting a 1/4 - 20 x 2” | |
Bolt then tighten with a phillips screwdriver. |
b. Attach the back of the chair to the arm by aligning holes and inserting a 1/4 - 20 x 2” Bolt thru the arm, leg and into the chair back, then tighten with a phillips screwdriver.
Repeat on both sides.
4.Attach the cross braces of the chair to the legs by aligning holes and inserting a 1/4 - 20 x 2” Bolt through the leg into the cross brace and tighten with a phillips screwdriver.
Repeat on other leg.
Do Front and Back cross braces.
5.Attach the center seat brace underneath to the back, insert a #10 x 3” screw thru the brace into the center of the bottom back support then tighten with the screwdriver.
Made in the U.S.A. www.kettlerusa.com info@kettlerusa.com