2548 ADIRONDACK ROCKING BENCH
Contents: | (18) 1/4 - 20 x 2” Bolts | ||
(1) | Seat, (1) Back | (6) | 1/4 - 20 x 2 1/2” Bolts |
(2) Arm Rests | (1) | #10 x 3” Screw | |
(2) | Front Chair legs | (10) Washers | |
(2) | Back Chair legs | (10) Locknuts | |
(2) | Cross Braces | Locknut Washer Bolt | |
(2) | Rocker Feet |
|
|
Tools Required:
#3 Phillips Head Screwdriver
7/16” Wrench
a. Align predrilled holes then insert bolts
1.to attach front legs.
b. Align predrilled holes then insert bolts to attach back legs.
1a. | 1b. |
2. | Place arm rest |
|
|
| on top of chair |
|
|
| legs, align front |
| Attach the back |
| predrilled holes, | 3. | |
| of the chair by | ||
| insert bolt. |
| aligning holes on |
|
|
|
Assembly Instructions
1. a. With the wing on the post facing front, |
align the predrilled holes on front leg to the seat |
and insert the 1/4 - 20 x 2” Bolts through the leg |
in thru the seat. Clean any plastic residue from the |
bolt then slide a washer on. Screw on the locknut |
and then tighten it with the wrench and phillips |
screwdriver. |
b. Align the predrilled holes on the back leg to |
the seat and insert the 1/4 - 20 x 2” Bolts through |
the leg in thru the seat. Clean any plastic residue |
from the bolt then slide a washer on. Screw on the |
locknut and then tighten it with the wrench and |
phillips screwdriver. Repeat on the other front leg. |
6.
the arm and the seat to insert bolt.
3b.
3a.
4.
Attach the braces to
the legs by5. aligning holes
and inserting a 2” bolt.
Attach the rocker to the legs by aligning holes to metal insert, use a 3” bolt.
Insert the bolt thru the center seat brace into the center of the back of bench.
2. Place arm rest on top of chair legs align the | |
front predrilled holes and insert the 1/4 - 20 x 2” | |
Bolts through the leg and in thru the arm. Clean | |
off any plastic residue then slide a washer on the | |
end of bolt. Screw on the locknut and then tighten | |
it with the wrench and phillips screwdriver. | |
3. | a. Attach the back of the chair to the seat |
| |
by aligning holes and inserting a 1/4 - 20 x 2” | |
Bolt then tighten with a phillips screwdriver. |
b. Attach the back of the chair to the arm by aligning holes and inserting a 1/4 - 20 x 2 1/2” Bolt thru the arm, leg and into the chair back, then tighten with a phillips screwdriver.
Repeat on both sides.
4.Attach the cross braces of the chair to the legs by aligning holes and inserting a 1/4 - 20 x 2” Bolt through the leg into the cross brace and tighten with a phillips screwdriver.
Repeat on other leg.
Do Front and Back cross braces.
5.Attach the rocker for the chair. Align the predrilled hole on the rocker to the metal isert at the bottom of each leg and insert a 1/4 - 20 x 2 1/2” bolt then tighten with the screwdriver.
Bolt rocker to both front and back legs.
6. Attach the center seat brace underneath to the back, insert a #10 x 3” screw thru the brace into the center of the bottom back support then tighten with the screwdriver.
| Made in the U.S.A. |
| www.kettlerusa.com |
Copyright © Kettler USA 309.01 | info@kettlerusa.com |
|