Adding Water
The LED Control Center of your Brewer will
indicate when the water level in the tank is low
or if the Water Reservoir has been removed by
illuminating the blue light next to ‘ADD WATER’.
The Brewer will not allow you to brew when
the blue 'ADD WATER' light is illuminated.
The Water Reservoir can be filled in two ways.
1. Lift off the Water Reservoir Lid and pour
water directly into the Water Reservoir
while it is still attached to the Brewer, then
replace the Lid.
2. Remove the Water Reservoir from Brewer
by first removing Lid from Reservoir, then
lifting Reservoir straight up and away from
Brewer. Fill with water. Place the Water
Reservoir back on the Brewer and replace
the Lid.
Brewing Hot Water
Your Brewer is able to produce a cup of hot
water for making hot chocolate, for use in
cooking, for making soups, etc. Simply raise
and lower the handle on the Brewer without
adding a K-Cup®portion pack. The green light
above the Brew Button on the LED Control
Center will flash. Be sure to have a mug or cup
on the Drip Tray and then press the Brew Button.
Purging the Brewer
If your Brewer has not been used for more
than one week, you should purge the water
from the inner tank.
1. If there is water in the Water Reservoir,
remove the Lid, then lift Reservoir straight up
and away from Brewer. Discard water, rinse
and refill with water. Place the Water Reservoir
back on the Brewer and replace the Lid. (If
there is no water in Reservoir, simply refill.)
2. Be sure the Brewer is turned on. Raise and
lower the handle on the Brewer without
inserting a K-Cup and wait until the red light
next to 'HEATING' turns off.
3. The green light above the Brew Button on
the LED Control Center will flash. Be sure to
have a mug or cup on the Drip Tray and then
press the Brew Button.
4. Repeat steps 2 and 3 two more times to
completely purge water from inner tank.
If you are experiencing any problems with
your Brewer, please contact Customer
Service at 1-866-901-BREW (2739).
SECTION 2

CONTROLS & INDICATORS

LED Control Center
Programming Auto off Timer Feature
Set the Brewer to turn off two hours after the
last brew.
a. Press the Power Button to turn on the Brewer.
b. Press the black button above the Power
Button on the LED Control Center to turn on
the Auto Off Timer feature. The green light
next to 'AUTO OFF' will become illuminated.
When the Auto Off Timer is enabled, your
Brewer will automatically turn off two hours
after your last brew.
c. To turn off
the Auto Off
Timer, sim-
ply press the
black button
again and
the green
light next to
'AUTO OFF'
will turn off.
89
IMPORTANT:Do not remove the Water
Reservoir during the brewing process.
Cleaning External Parts
Regular cleaning of the Brewer’s external com-
ponents is recommended.
1. Never immerse the base unit in water or
other liquids. The Housing and other external
components may be cleaned with a soapy,
damp, non-abrasive cloth.
2. The Drip Tray can accumulate up to 8
ounces of overflow. The Drip Tray and Drip
Tray Plate should be periodically inspected and
rinsed clean. To remove the Drip Tray
Assembly, simply slide it toward you, keeping it
level at all times to avoid spilling. The Drip Tray
and Drip Tray Plate are dishwasher safe.
Cleaning the K-Cup®Portion Pack
Holder Assembly
1. Cleaning the Parts
The K-Cup Holder Assembly is dishwasher safe.
To remove from the Brewer, open the cover by
lifting the Handle. Grasp the top of the K-Cup
Holder with one hand while pushing up on the
bottom of the K-Cup Holder from underneath
with the other until it releases. After cleaning,
align the K-Cup Holder with the opening using
the two front ribs as a guide and snap into
place from the top.
2. Cleaning the Funnel
The Funnel can be removed from the K-Cup
Holder by pulling on it until it snaps off. The
Funnel is dishwasher safe. To replace it just snap
it back onto the K-Cup Holder Assembly.
3. Cleaning the Exit Needle
The Exit Needle is located on the inside bottom
of the K-Cup Holder Assembly. Should a clog
arise due to coffee grinds, it can be cleaned
using a paper clip or similar tool. Remove K-
Cup Holder, insert the paper clip into the
Needle to loosen the clog and push it out. The
K-Cup Holder is dishwasher safe.
Cleaning the Water Reservoir and
Water Reservoir Lid
The Water Reservoir Lid should be cleaned
with a damp soapy non-abrasive cloth. Lid
should not be put into the dishwasher.
The Water Reservoir can be placed into the
dishwasher for cleaning or can be cleaned with
soapy water and rinsed thoroughly.
Do not dry the inside of the Water Reservoir
with a cloth as lint may remain.
De-Scaling Your Brewer
Mineral content in water varies from place to
place. Depending on the mineral content of the
water in your area, calcium deposits or scale
may build up in your Brewer. Scale is non-
toxic, but left unattended, it can hinder Brewer
performance. De-scaling your Brewer helps
maintain the heating element, and other inter-
nal parts of the Brewer that come in
contact with water.
The Brewer should be de-scaled every 6
months to ensure optimal performance. It is
SECTION 3

CLEANING & MAINTENANCE

CAUTION: There are sharp needles that
puncture the K-Cup above the K-Cup Holder
and in the bottom of the K-Cup Holder. To
avoid risk of injury, do not put your fingers
in the K-Cup Chamber.
K-Cup Holder
Assembly
K-Cup Holder
Funnel
CAUTION: Please rinse the Water Reservoir
thoroughly after cleaning to ensure that no
cleaners or cleaning solutions remain in
this area as they may contaminate the
water supply in the Brewer.