TweeterMounting

 

The tweeter can be mounted one of three ways: flush, angled-surface and angled mounting.

 

For flush mounting applications, please refer to the illustration in Figure 5. Choose a flat

 

location on the panel with space behind the panel to allow room for the mounting nut. After

 

checking the clearances, cut a 1 9/16” (4cm) diameter mounting hole in the panel. Place the

 

shorter mounting nut behind the panel (only use the longer mounting nut if panel thickness

 

prohibits the use of the shorter mounting nut). Feed the wire through the optional tweeter

 

flange, the hole in the panel and the mounting nut. Mount the tweeter by screwing the

 

mounting nut onto the tweeter.

 

For angled-surface mounting applications use the angled-surface mount cup as a template

 

and pre-drill one 7/64” (2.5mm) screw hole for attaching the angled-mounting cup to the

 

panel, and a 5/16” (8mm) hole for the wires. A M3 pan-cross head wood screw is supplied

INSTALLATION

to attach the mounting cup to the panel. Position the tweeter over the attached angled-

mounting cup and press it into position. See Figure 6.

For angled mounting applications choose a flat location on the panel with space behind the

panel to allow room for the mounting nut and back angle ring. After checking the

clearances, cut a 1 9/16” (4cm) diameter mounting hole in the panel. Place the front angle

 

ring (does not fit through the longer tweeter mounting nut) in front of the panel. Then place

 

the wire and tweeter through the tweeter flange, front angle ring and into the panel. Next

 

place the wire through the back angle ring (fits through the longer tweeter mounting nut),

 

place the back angle ring over the rear of the tweeter, and line-up the narrow part of the

 

front angle ring for the preferred angle of operation. Place the wire through the longer

 

tweeter mounting nut and loosely tighten the mounting nut around the tweeter. Rotate all the

 

parts in unison until the tweeter is angled in the desired direction. Secure the assembly by

 

tightening the tweeter mounting nut. See Figure 7.

 

Wiring

 

Hooking up the Kicker DS-Series Component Speakers is easy. Mount the external

 

crossover in a location free and clear of water and mechanical components of the vehicle

 

with the enclosed phillips-head wood screws. The positive and negative leads on the

 

speakers are terminated with connectors of different shapes and sizes that intuitively

Figure 5

Flush Mount

Panel

Figure 6

M3 Screw

Angled-Surface Mount

Panel

Figure 7

Angled Mount

Panel

Optional Tweeter Flange

Tweeter

Shorter Mounting Nut

Tweeter

Angled-Surface Mount Cup

Tweeter Flange

Back Angle Ring

Tweeter

Front Angle Ring

Longer Mounting Nut

connect to the external crossover’s connectors. After connecting the speakers to the

external crossover, connect the external crossover to the source unit or amplifier in

accordance with its owner’s manual. For reference, the Gray wire is Positive and the Black

wire is Negative on the external crossover.

WiringMultipleSpeakers

Modern high performance component system speakers have a lower DC Resistance than what used to be available. The Kicker DS-Series component system speakers are rated at four ohms and work with any source unit or amplifier designed to operate at a four ohm load. If you want to use two DS-Series component system speakers (two midrange/woofers and two tweeters) on each channel of

 

your source unit or amplifier wire the

 

Figure 4

 

 

 

 

speakers in series, as shown below. This

Source Unit or Amplifier

 

 

External Crossover

 

will improve the sound quality, lower the

 

 

 

 

 

 

 

 

 

 

 

 

total harmonic distortion and lessen the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

thermal load at the source unit or

 

 

 

 

 

 

 

High Frequency Output

 

amplifier. This may prevent an amplifier

 

 

 

 

 

 

 

 

Two DS-Series Component

 

 

Attenuation Switch: 0, 3 & 6dB

 

from shutting down, due to over-current

 

 

 

 

 

Speakers wired in series to

 

 

 

 

 

protection circuitry. See Figure 4.

 

a single channel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

DSCOMPONENTSYSTEM

 

 

 

Performance

Model:

DS600.2

DS650.2

DS680.2

 

 

 

 

 

Woofer Size, in (mm)

6

(160)

6.5 (165)

6x8 (160x200)

Tweeter Size, in (mm)

3/4 (20)

3/4 (20)

3/4 (20)

Dome Material

Titanium

Titanium

Titanium

Rated Impedance, ohm (DC Resistance, ohm)

4

(3)

4

(3)

4

(3)

Power Handling Watts, Peak (RMS)

120 (60)

120 (60)

90 (45)

Sensitivity [SPLo], dB @ 1W, 1m

90

90

90

Effective Frequency Range, Hz

35-21k

35-21k

40-21k

Woofer Mounting Hole Diameter, in (cm)

4

13/16 (12.3)

5

1/2 (14)

5x7 3/16 (12.7x18.3)

Woofer Top Mount Depth, in (cm)

1

7/8 (4.8)

1

13/16 (4.6)

2

3/8 (6)

Woofer Bottom Mount Depth, in (cm)

2

3/16 (5.5)

2

(5.1)

2

3/4 (7)

Flush Mounting Tweeter Hole Diameter, in (cm)

1

9/16 (4)

1

9/16 (4)

1

9/16 (4)

High Pass, dB, at Frequency, Hz

12, 4000

12, 4000

12, 4000

Low Pass, dB, at Frequency, Hz

12, 4000

12, 4000

12, 4000

High Frequency Output Attenuation, dB

0, 3 & 6

0, 3 & 6

0, 3 & 6

Bolt-Thru Grilles

Yes

Yes

No

PERFORMANCE

5

Page 2 Page 4
Page 3
Image 3
Kicker DS600.2 manual TweeterMounting, Wiring MultipleSpeakers, Performance
Page 2 Page 4

DS600.2 specifications

The Kicker DS600.2 is a powerful car audio amplifier designed to deliver superior sound quality and performance to automotive sound systems. Known for its compact design and impressive specifications, this amplifier stands out in the crowded market of audio products. It is engineered to enhance the listening experience, catering to both casual music enthusiasts and dedicated audiophiles.

One of the main features of the Kicker DS600.2 is its 2-channel operation, which allows users to connect their front and rear speakers directly to the amplifier. This enables the amplifier to deliver exceptional power and clarity, making it suitable for a variety of setups, from simple upgrades to more complex installations. The amplifier is capable of producing up to 300 watts of total power, boasting an impressive RMS output of 75 watts per channel at 4 ohms and 90 watts per channel at 2 ohms. This ensures that your speakers receive enough power to perform at their best without distortion.

The Kicker DS600.2 is built using high-quality materials that ensure durability and performance over time. The amplifier features a cast aluminum heat sink, which helps maintain optimal operating temperatures, thereby increasing efficiency and longevity. Additionally, the DS600.2 incorporates high and low-pass crossover filters, allowing users to customize sound output to their preferences. This feature is particularly useful for optimizing bass response or tailoring the frequency range of mid-range and treble drivers.

Technologically, the Kicker DS600.2 is designed with user convenience in mind. The amplifier includes a variable input sensitivity control that accommodates different source units, allowing for easy integration with existing audio systems. The compact design of the amplifier makes it easier to install in various vehicle models, offering more flexible placement options.

Another notable characteristic of the Kicker DS600.2 is its low noise and high signal-to-noise ratio, which minimizes interference and ensures clear audio reproduction, even at higher volumes. The inclusion of a fused power supply and built-in protection circuitry further enhances the reliability of the amplifier, safeguarding it against short circuits and overheating.

In summary, the Kicker DS600.2 is an exceptional choice for anyone looking to upgrade their vehicle's sound system. With its powerful performance, robust construction, and user-friendly features, this amplifier offers a remarkable combination of sound quality and reliability that can elevate the in-car listening experience.
Top Page Image Contents