2007 WX
|
|
|
| WX.1SeriesAmplifier |
|
|
|
| Owner’sManual |
|
| Model: | WX10000.1 | |
| SubwooferAmplifier |
| ||
|
|
|
| |
|
| Authorized Kicker Dealer: __________________________ | ||
| Congratulations on your | |||
|
|
|
| |
| KICKER purchase | Purchase Date: | __________________________ | |
| Please record your purchase | Amplifier Model Number: | WX10000.1 | |
| information and keep your sales | |||
| receipt for validation of warranty. | Amplifier Serial Number: | __________________________ | |
|
| |||
| INSTALLATION | The Kicker Warhorse amplifier was specifically designed for competition car audio. Sporting 10,000 | |||
supply amplifies each polarity of the audio signal separately through its two voice coil outputs to | ||||
| RMS watts of pure Kicker power, the | |||
traditional methods of amplification. While most amplifiers use a power supply combined with an amplification circuit to amplify the audio signal, the Warhorse skips a step by amplifying the audio signal directly from its patent pending
optimally drive
|
| 100 | Figure 1 |
|
|
|
|
|
| |
| The patent pending |
|
|
|
|
|
|
|
|
| 90% |
| 80 |
|
|
|
|
|
|
| 75% | |
| design of the Warhorse amplifier is the | Y |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |||
| efficiency at full power with a 2 ohm load. | ICIENCFF |
|
|
|
|
|
|
|
|
|
| most powerful and efficient design |
| 60 |
|
|
|
|
|
|
|
|
| available in mobile audio, rated at 90% |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
| The graph compares the Warhorse | E | 40 |
|
|
|
|
|
|
|
|
% |
|
|
| KICKER PATENT PENDING | ||||||
| amplifier’s efficiency ratings to those of | 20 |
|
| |||||||
|
|
| ||||||||
|
|
|
|
|
|
|
|
| ||
| industry standard Class D amplifiers. |
|
|
| HIGH QUALITY CLASS D DESIGN |
|
|
| |||
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| |
Installation . . . as easy as 1, 2, 3 |
| 0 | 0.1 | 0.2 | 0.5 | 1.0 | 2.0 | 4.0 | 8.0 | 10 |
|
| |||||||||
|
|
|
| POWER OUTPUT (KW) |
|
|
| |||
|
|
|
|
|
|
|
| |||
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The amplifier should be mounted as close as possible to the battery network and be electrically isolated from the vehicle ground. The distance from the battery network to the amplifier should not exceed 48” (122cm). It is important to mount the amplifier before running any wires or supplying power to the amplifier. The amplifier secures to the vehicle with an insertable mounting bracket used in combination with two mounting holes located on the bottom plate of the control panel. You are solely responsible for securely fastening the WX amplifier in your vehicle.
Before mounting the amplifier, the control panel shield must be removed. The control panel should remain accessible for adjustment, leaving enough room to access the mounting holes and remove or attach the control panel shield. Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifier. After choosing the best location, secure the mounting bracket to the vehicle. Use the bracket as a template to drill nine (9) holes with a 3/16” (4.8mm) bit into the appropriate locations. Attach the bracket to the mounting location with the nine (9) supplied #10 (5mm) screws inserted through the nine (9) included screw insulators.
Next, slide the amplifier over the mounting bracket and into the mounting slot. Make sure the mounting bracket is properly inserted into the mounting slot and locate the two mounting holes on the bottom plate of the control panel. Use the mounting holes as a template and drill two (2) holes using a 3/16” (4.8mm) bit into the appropriate locations. Secure the bottom plate of the control panel with the two (2) #10 (5mm) screws.
Caution The Kicker WX amplifier outputs extremely high voltage signals from the voice coil (speaker) outputs and can cause serious injury or death from electrocution. It is imperative to read the manual carefully and follow all of the recommended safety precautions before installing the WX amplifier.
| Figure 2 | Before mounting the amplifier, be sure there is adequate space in the mounting position |
| to take the control panel shield on or off and to easily access the amplifier’s controls. | |
|
| |
1. |
| Control Panel Shield |
Remove the two (2) screws | ||
securing the control panel
shield to the amplifier chassis.
2. Remove the control panel shield from the amplifier so the mounting holes on the bottom plate of the control panel will be accessible.
3.After determining the best mounting position for the amplifier, use the mounting bracket as a template to drill nine (9) holes with a 3/16” (4.8mm) bit into the appropriate locations. Attach the bracket to the mounting location with the nine (9) supplied #10 (5mm) screws inserted through the nine (9) included screw insulators.
Mounting Bracket
Nine (9) Supplied
Screw Insulators
Nine (9) Supplied 
#10 (5mm) screws 
4.Slide the Warhorse over the mounting bracket and insert the mounting bracket into the mounting slot on the bottom of the amplifier.
Warhorse Amplifier
The amplifier is very heavy. Assistance may be necessary to lift and position the amplifier.
Mounting Bracket
5.Locate the additional mounting holes on the bottom plate of the control panel. Use the mounting holes as a template to drill two holes using a 3/16” (4.8mm) bit into the appropriate locations. Secure the bottom plate of the control panel with the two (2) #10 (5mm) screws. You are solely responsible for securely fastening the amplifier in your vehicle.
Mounting Holes
Control Panel
(Top View)
2 | WX10000.1AMPLIFIER | 3 |
