Kidde 1235E warranty Architectural and Engineering Specifications, Installation of Smoke Alarm

AC Wire-In Smoke Alarm Unit Number 1235E

Architectural and Engineering Specifications

The smoke alarm shall be Kidde Unit 1235 or approved equal.It shall be powered by a 120VAC, 60Hz source. The unit shall incorporate an ionization sensor with nominal sensitivity of 0.64%/ft. The temperature operation range shall be between 40˚F (4˚C) to 100˚F (38˚C) and the humidity operating range shall be 5% - 95% relative humidity.

The smoke alarm can be installed on any standard single gang electrical box, up to a 4” octagon junction box. The electrical connection (to the alarm) shall be made with a plug-in connector. A maximum of 24 Kidde devices can be interconnected in a multiple station arrangement. The inter- connect system must not exceed the NFPA (National Fire Protection Association) limit of 18 initiating devices, of which 12 can be smoke alarms. With 18 initiating devices (Smoke, heat, CO, etc.), interconnected, it is still possible to interconnect 6 strobe lights and or relay modules. The alarm shall provide optional tamper resistance that deters removal of the unit from the wall or ceiling.

The alarm shall include a piezoelectric horn that is rated at 85 decibels at 10 feet. The unit shall incorporate 2 LED’s. A green LED will be constant- ly “ON” when AC power is present and will flash until reset (alarm memory) to indicate which alarm was the originating alarm at the last incident. Pressing the test button will reset the alarm memory condition. A red LED will flash once every 30-40 seconds to indicate the alarm is operating proper- ly and will flash once per every 1.5 seconds when the unit is alarming and will remain so until the air is cleared.

The unit shall at a minimum meet the requirements of UL217, NFPA72, (chapter 11 2002 edition) The State of California Fire Marshall, NFPA101 (One and two family dwellings), Federal Housing Authority (FHA, Housing and Urban Development (HUD).

Installation of Smoke Alarm

The smoke alarm should be installed to comply with all local codes having jurisdic- tion in your area, Article 760 of the National Electric Code, and NFPA 72. Make certain all alarms are wired to a single, continuous (non-switched) power line, which is not protected by a ground fault interrupter. A maximum of 1000 ft. of wire can be used in the interconnect system. Use standard UL listed household wire (18 gauge or larger as required by local codes).

FUSE OR CIRCUIT BREAKER

L

N

BLACK	RED
WHITE

First	Additional
Alarm	Alarms

Technical Specifications

Unit Number:	1235E
UPC:	0-25417-12351-7
Power Source:	120VAC
Sensor:	Ionization
Audio Alarm:	85dB at 10ft
Temperature Range:	40˚F (4.4˚C) to 100˚F (37.8˚C)
Humidity Range:	5%-95% relative humidity (RH)
Size:	5.6” in diameter x 1.55” depth
Weight:	.6lbs
Interconnects:	Up to 24 Kidde devices
LED:	Green, receiving ac power
	Red, alarm mode
Warranty:	5 year limited
	5.6"	1.55"

Ordering Information

Gift Box UPC:	0-25417-12351-7
Part			Dimensions		Case/	Layers/	Skid
Number	I 2 of 5	Pack Quantity	(w x d x h inches)	Weight	Skid	Skid	Weight
1235**	N/A	Individual	5.75 x 1.75 x 5.75	.6lbs	N/A	N/A	N/A
1235E	200 25417 12351 1	Master Pack (12 units)	5.25 x 10.5 x 10.75	7.2lbs	128	16	921.6lbs
**Not for sale by individual unit
						1	12
						UNIT	MASTER PACK

Distributed by:

1394 South Third Street, Mebane NC 27302

1-800-880-6788 • www.kiddeus.com