Kidde I12040 Architectural and Engineering, Installation of Smoke Alarm, Specifications, Model

120V AC/DC Wire-in Smoke Alarm	Part Number 21006378
Battery Backup	Model i12040

Architectural and Engineering	Installation of Smoke Alarm
Specifications	The smoke alarm must be installed to comply with all local codes having jurisdiction
	in your area. All wiring shall be in accordance with articles 210 and 300.3(B) of
The smoke alarm shall be Kidde model i12040 or approved equal. It shall be	the US National Electrical Code, ANSI / NFPA 70 and NFPA 72. The multiple station
	interconnect wiring must be in the same raceway as the AC power wiring. In addi-
powered by a 120VAC, 60Hz source along with a 9V battery backup. The
	tion the resistance if the interconnect wiring shall be a maximum of 10 ohms.
unit shall incorporate an ionization sensor with nominal sensitivity of .50 to
	Make certain all alarms are wired to a single, continuous (non-switched) power
.98%ft. The temperature operation range shall be between 40˚F and 100˚F	line, which is not protected by a ground fault interrupter. A maximum of 1000 ft.
(4˚C and 38˚C) and the humidity operating range shall be 5% - 95% relative	of wire can be used in the interconnect system. Use standard UL listed household
humidity.	wire as required by code.	FUSE OR CIRCUIT BREAKER
The smoke alarm can be installed on any standard single gang electrical		L
		N
box, up to a 4” octagon junction box. The electrical connection (to the alarm)
shall be made with a plug-in connector. A maximum of 24 Kidde devices can
be interconnected in a multiple station arrangement. The interconnect system			BLACK		RED
				WHITE
must not exceed the NFPA (National Fire Protection Association) limit of 18
initiation devices, of which 12 can be smoke alarms. With 18 initiating devic-
es (smoke, heat, CO, etc.), interconnected, it is still possible to interconnect			First			Additional
6 strobe lights and or relay modules. The unit shall provide optional tamper			Alarm			Alarms
resistance that deters removal of the unit from the wall or ceiling.	Technical Specifications
The alarm shall include a test button that will electronically simulate the
presence of smoke and cause the unit to go into alarm. This sequence tests	Model Number:	i12040
the unit’s electronics, battery and horn to ensure proper operation.
	UPC:	0-47871-40381-3
The unit shall include a piezoelectric horn that is rated at 85 decibels at
	Power Source:	120VAC (80mA) with 9V Battery Back Up
10 feet. The unit shall include Smart HushTM feature that silences the unit for
approximately 7 minutes if a nuisance condition occurs. The unit shall also
	Sensor:	Ionization
include a low battery warning utilizing a brief alarm chirp every 30-40 sec-
onds for a minimum of seven (7) days.	Audio Alarm:	85dB at 10ft
The unit shall incorporate red and green LED indicators. The green LED	Temperature Range:	40˚F (4.4˚C) to 100˚F (37.8˚C)
(when illuminated) indicates the presence of AC power. The red LED (located
under the TEST/Hush button) has four modes of operation:	Humidity Range:	5%-95% relative humidity (RH)
Standby Condition: The red LED will flash every 30-40 seconds to indicate	Size:	5.6” in diameter x 1.55” depth
that the smoke alarm is operating properly. Alarm Condition: When the
	Weight:	.5lb
alarm senses products of combustion and goes into alarm the red LED will
flash one flash per second. The flashing LED and pulsating alarm will continue
	Interconnects:	Up to 24 Kidde devices
until the air is cleared. When units are interconnected, only the red LED of
the alarm that senses the smoke or is being tested (the originating unit) will	Wiring:	Quick-connect plug with 8” pigtails
flash. All other units in the interconnected system will sound an alarm but
	LED:	Red, 4 modes of operation
their red LED’s will NOT flash. Alarm Memory: This smoke alarm is equipped
with an alarm memory, which provides a visual indication when an alarm has		Green, indicates AC power
been activated. The red LED will illuminate for about 1.5 seconds every 16
	Warranty:	10 year limited
seconds to indicate the memory condition. Smart HushTM Mode: The red LED
will illuminate for 1.5 seconds every 8 seconds, indicating the smoke alarm is
in the Smart HushTM Mode.
The unit shall at a minimum meet the requirements of UL217, NFPA72,
(chapter 11), The State of California Fire Marshall, NFPA 101 (One and
two family dwellings) Federal Housing Authority (FHA), Housing and Urban
Development (HUD). It shall also include a 10-year manufacture’s limited warranty.

Ordering Information

Ordering					Dimensions		Case/	Layers/	Skid
Number	UPC		I2F5	Pack Quantity	(w x d x h inches)	Weight	Skid	Skid	Weight
N/A	0-47871-40381-3		N/A	individual*	5.75 x 1.5 x 5.75	0.5 lbs	N/A	N/A	N/A
21006378	0-47871-40381-3		100-47871-40381-0	Cut Case (6 units)	6.5 x 13.25 x 6	3 lbs	147	7	441 lbs
21006373	0-47871-09970-2		200-47871-09970-2	Bulk Pack (6 units)	6 x 10.5 x 6	3 lbs	147	7	441 lbs
21006930	0-47871-40381-3		300-47871-40381-4	Display Pallet (36 units)	20 x 24 x 40	20lbs	4	1	90 lbs
Alk. Btry 21006928	0-25417-12751-5		100-25417-12751-2	Cut Case (6 units)	6.5 x 13.25 x 6	3 lbs	147	7	441 lbs
Lith. Btry 21006929	0-25417-01276-7		100-25417-01276-4	Cut Case (6 units)	6.5 x 13.25 x 6	3 lbs	147	7	441 lbs
21006375**	0-47871-27552-6		100-47871-27552-3	Cut Case (6 units)	6.5 x 13.25 x 6	3 lbs	147	7	441 lbs
21006372**	0-47871-09969-9 100-47871-09969-3			Cut Case (3 Twin Packs)	6.5 x 13.25 x 6	3 lbs	147	7	441 lbs
*Not for sale by individual unit		**Includes Wiring Adapters

1016 Corporate Park Drive Mebane NC 27302 1-800-880-6788 www.Kidde.com

Distributed by:

P/N: KL-i12040 sheet rev. 01-2009