Kidde I12080 warranty Architectural and Engineering Specifications, Installation of Smoke Alarm

120V AC/DC Smoke Alarm

Safety Light

Architectural and Engineering Specifications

The smoke alarm shall be Kidde model i12080 or approved equal. It shall be ­powered by a 120VAC, 60Hz source along with a 9V battery back up. The unit shall incorporate an ionization sensor with nominal sensitivity of .50 to .85%/ft.

The temperature operation range shall be between 40˚F and 100˚F (4˚C and 38˚C) and the humidity operation range shall be 5% - 95% relative humidity.

The smoke alarm can be installed on any standard single gang electrical box, up to a 4” octagon junction box. The electrical connection (to the alarm) shall be made with a plug-in connector. A maximum of 24 Kidde devices can be inter- connected in a multiple station arrangement. The interconnect system must not exceed the NFPA (National Fire Protection Association) limit of 18 initiating devices, of which 12 can be smoke alarms. With 18 initiation devices (smoke, heat, CO, etc.), interconnected, it is still possible to interconnect 6 strobe lights and or relay modules. The unit shall provide optional tamper resistance that deters removal of the unit from the wall or ceiling.

The alarm shall include a safety light that shall be powered by a 9V alkaline battery. The safety light shall provide 15 minutes of light when the alarm is sounding. The alarm shall include a test button that will electronically simulate the presence of smoke and cause the unit to go into alarm. This sequence tests the unit’s electronics, battery and horn to ensure proper operation.

The unit shall include a piezoelectric horn that is rated at 85dB at 10 feet.

The unit shall include Smart HushTM feature that silences the unit for approximately 7 minutes if a nuisance condition occurs. The unit shall also include a low battery warning utilizing a brief alarm chirp every 30-40 seconds for a minimum of seven (7) days.

The unit shall incorporate red and green LED indicators. The green LED (when illuminated) indicates the presence of AC power. The red LED (located under the TEST/Hush button) has four modes of operation:

Standby Condition: The red LED will flash every 30-40 seconds to indicate that

the smoke alarm is operating properly. Alarm Condition: When the alarm senses products of combustion and goes into alarm the red LED will flash one flash per second. The flashing LED and pulsating alarm will continue until the air is cleared. When units are interconnected, only the red LED of the alarm that senses the smoke or is being tested (the originating unit) will flash. All other units in the interconnected system will sound an alarm but their red LED’s will NOT flash. Alarm Memory: This smoke alarm is equipped with an alarm memory, which provides a visual indication when an alarm has been activated. The red LED will illuminate for about 1.5 seconds every 16 seconds to indicate the memory condition. Smart HushTM Mode: The red LED will illuminate for 1.5 seconds every 8 seconds, indicating the smoke alarm is in the Smart HushTM Mode.

The unit shall at a minimum meet the requirements of UL217, NFPA72, (chapter 11), The State of California Fire Marshall, NFPA 101 (Oneand two family dwellings) Federal Housing Authority (FHA), Housing and Urban Development (HUD).

It shall also include a 10-year manufacture’s limited warranty.

Part Number 21006379

Model i12080

Installation of Smoke Alarm

The smoke alarm must be installed to comply with all local codes having jurisdiction in your area. All wiring shall be in accordance with articles 210 and 300.3(B) of the US National Electrical Code, ANSI / NFPA 70 and NFPA 72. The multiple station intercon- nect wiring must be in the same raceway as the AC power wiring. In addition the resistance if the interconnect wiring shall be a maximum of 10 ohms. Make certain all alarms are wired to a single, continuous (non-switched) powerline, which is not pro- tected by a ground fault interrupter. A maximum of 1000 ft.of wire can be used in the interconnect system. Use standard UL listed household wire as required by code.

FUSE OR CIRCUIT BREAKER

L

N

BLACK	RED
WHITE

First	Additional
Alarm	Alarms

Technical Specifications

Model:	i12080
UPC:	0-47871-40382-0
Power Source:	120VAC (80mA), 60HZ, 9V battery backup
Sensor:	Ionization
Audio Alarm:	85dB at 10ft
Temperature Range:	40˚F (4.4˚C) to 100˚F (37.8˚C)
Humidity Range:	5% - 95% relative humidity (RH)
Size:	5.6” in diameter x 1.55” depth
Weight:	.5lb
Interconnects:	Up to 24 Kidde devices
LED:	Green, receiving ac power
	Red, 4 modes of operation
Warranty:	10 year limited
	5.6”	1.5”

Ordering Information

Ordering				Dimensions		Case/	Layers/	Skid
Number	UPC	I2F5	Pack Quantity	(w x d x h inches)	Weight	Skid	Skid	Weight
N/A	0-47871-40382-0	N/A	individual*	5.75 x 1.5 x 5.75	0.5 lbs	N/A	N/A	N/A
21006379	0-47871-40382-0	100-47871-40382-7	Cut Case (6 units)	6.5 x 13.25 x 6	3 lbs	147	7	441 lbs

*Not for sale by individual unit

1016 Corporate Park Drive Mebane NC 27302 1-800-880-6788 www.Kidde.com

Distributed by:

P/N: KL-i12080 sheet rev. 01-2009