AC Powered, Digital Display, Plug-In

Carbon Monoxide Alarm

Architectural and Engineering Specifications

The carbon monoxide alarm shall be Kidde Unit Number KN-COPP-3 (part number 900-0076) or approved equal. It shall be powered by a 120VAC, 60 Hz source along with a 9V battery back up. The tempera- ture operating range shall be between 40˚F and 100˚F (4˚C and 38˚C) and the humidity operating range shall be 5% - 95% relative humidity. The CO sensor shall be of a fuel cell design and shall meet the

sensitivity requirements of Underwriters Laboratories UL2034 Single and Multiple Station Carbon Monoxide Alarms. The unit shall provide accuracy of +/-20% + 15 parts per million (ppm) when reading CO con- centration levels.

The alarm shall include an attached plug that can be installed in any outlet following the UL/NFPA/Manufacturer’s recommended guidelines. The plug can be snapped into the back of the unit and shall be capable of being rotated so the alarm remains vertical independent of whether the electrical socket is mounted vertically or horizontally. In addition, the alarm plug will have an attached extension cord so the unit can be plugged into the wall outlet and then placed on a table or shelf.

The unit shall incorporate a digital display that meets the sensitivity requirements of UL 2034. The display will identify the levels of CO in parts per million (ppm) once that level reaches 30ppm (i.e.: “abnormal” levels). The display will have a red dot in the lower right corner that will blink to indicate the normal operation.

The alarm shall include a test button that will electronically simulate the presence of CO and cause the unit to go into alarm. This sequence tests the unit’s electronics to ensure proper operation.

In accordance with UL 2034, the CO sensor will not alarm to levels of CO below 30 ppm and will alarm in the following time range when exposed to the corresponding levels of CO.

70 ppm CO concentration

60

– 240 minutes

150 ppm CO concentration

10

– 50 minutes

400 ppm CO concentration

4 – 15 minutes

The alarm shall include a piezoelectric horn that is rated at 85 decibels at 10 feet. When the unit detects carbon monoxide, the alarm pattern will be four (4) short beeps – followed by five (5) seconds of silence – followed by four (4) short beeps. A number reading will appear on the digital display identifying the measured CO concentration (in ppm).

Part Number 900-0076

Model KN-COPP-3

The unit shall include a peak level memory feature that will store the peak CO level sensed since the unit was last reset. The peak CO level stored in the unit’s memory shall be displayed (in ppm) on the digital display by pressing the appropriate button on the unit. The memory shall also be capable of being reset.

The unit shall also indicate a low battery warning utilizing each of the following methods: a brief alarm chirp occurring approximately once per minute and having “Lb” displayed on the digital display.

The unit shall be listed to UL 2034. It shall also include a 5-year manufacturer’s limited warranty.

Technical Specifications

Part Number:

900-0076

Model:

KN-COPP-3

UPC Number:

7-84908-00760-5

Power Source:

120VAC

Sensor:

Electrochemical

Audio Alarm:

85dB at 10ft

Temperature Range:

40˚F (4.4˚C) to 100˚F (37.8˚C)

Humidity Range:

5%-95% relative humidity (RH)

Size:

6.0625”L x 3.75”W x 1.75”H

Weight:

1lb

Interconnects:

No

Wiring:

Plug-In

LED:

Displays CO concentration in PPM

Warranty:

5 year limited

3.75"

1.75"

 

6.0625"

Ordering Information

UPC: 7-84908-00760-5

Part

 

 

Dimensions

 

Case/

Layers/

Skid

Number

I 2 of 5

Pack Quantity

(w x d x h inches)

Weight

Skid

Skid

Weight

 

 

 

 

 

 

 

 

900-0076**

N/A

Individual

7.25 x 2 x 10.75

1lb

N/A

N/A

N/A

 

 

 

 

 

 

 

 

900-0076-01

107 84908 00760 2

PDQ (2 units)

8 x 6.25 x 11.25

3lbs

105

3

475lbs

 

 

 

 

 

 

 

 

900-0076-14

407 84908 00760 3

Master Pack (4 units)

7.5 x 12 x 11.5

5lbs

100

5

660lbs

 

 

 

 

 

 

 

 

900-0076-16­

207 84908 00760 9

Cut Case (12 units)

14.75 x 17.5 x 12

14lbs

18

3

300lbs

 

 

 

 

 

 

 

 

900-0076-036

307 84908 00760 6

Power Tower (36 units)

20 x 24 x 41 (incl. pallet)

40lbs

3

3

120lbs

 

 

 

 

 

 

 

 

21005294

047871 05294 3

Bulk Pack (6 units)

12.5 x 6.25 x 7

6lbs

105

3

630lbs

 

 

 

 

 

 

 

 

**Not for sale by individual unit

1016 Corporate Park Drive Mebane NC 27302 1-800-880-6788 www.Kidde.com

Distributed by:

KL-900-0076 sheet

rev. 01-2009

Page 1
Page 2
Image 2
Kidde KN-COPP-3 warranty Architectural and Engineering Specifications, Technical Specifications, Ordering Information
Page 1

KN-COPP-3 specifications

The Kidde KN-COPP-3 is an advanced carbon monoxide (CO) and explosive gas detector designed to enhance safety in residential and commercial environments. One of its most notable features is its ability to detect both carbon monoxide and explosive gases like natural gas and propane, making it a dual-function device.

This detector is equipped with an electrochemical sensor that is highly sensitive to carbon monoxide, ensuring early detection of potentially dangerous gas levels. It can detect CO concentrations as low as 30 parts per million (ppm), which is vital for ensuring occupant safety. The device has a loud alarm that sounds when it detects high levels of CO, alerting residents to evacuate the premises immediately.

The Kidde KN-COPP-3 is designed for ease of use and convenience. It features a digital display that shows CO levels in real-time, allowing users to monitor the situation at a glance. Additionally, the unit is equipped with a peak level memory that stores the highest CO concentration detected since the last reset, providing valuable information in case of an alarm event.

In terms of installation, the KN-COPP-3 is easy to set up, requiring just a standard outlet for power. It also includes a backup battery system that ensures it remains operational even in the event of a power outage. This reliability is paramount for safety, as carbon monoxide is a colorless, odorless gas that can pose serious health risks.

Another characteristic of the Kidde KN-COPP-3 is its test and reset button, which allows users to routinely check the functionality of the alarm. Regular testing is important to ensure that the device is in working order and ready to respond in an emergency.

The device also incorporates a low battery warning feature, which alerts users when it's time to replace the batteries or the unit itself, further ensuring safety and peace of mind.

In conclusion, the Kidde KN-COPP-3 is a reliable and user-friendly carbon monoxide and explosive gas detector that combines advanced technology with essential safety features. Its dual detection capabilities, real-time monitoring, and dependable alarm system make it a crucial addition to any home or business to protect occupants from the dangers of CO and explosive gases.
Top Page Image Contents