Manuals / King Kutter / Lawn and Garden / Tiller

King Kutter 999995 Rotary Tiller Assembly Instructions, Before Putting Rotary Tiller Into Service

Models: 999995

1 36
Download 36 pages 15.92 Kb
Page 8
Image 8

ROTARY TILLER ASSEMBLY INSTRUCTIONS

STEP 1 With rotary tiller still in crate, lay flat on a level surface. Cut banding straps on the two (2) up right crate posts.

STEP 2 Remove the top & upper side sections of the crate, leaving the rotary tiller resting on the bottom section. You may take the tiller off of crate but you must swing stand arm down and lock in position. (See Figure D) Snap stand out of clip, straight out, then swivel the stand down to locked position.

STEP 3 Remove tie wire holding the PTO shaft and set aside PTO.

STEP 4 Attach tiller according to your tractors manual and using the instructions on pages 16 and 17.

STEP 5 Install tail back plate chain.

STEP 6 Install PTO shaft as outlined in the Attaching to Tractor Section, pg 16- 19.

Note: The safety chains on the PTO shaft should be attached to the tractor and tiller to prevent the plastic safety shield from rotating.

BEFORE PUTTING ROTARY TILLER INTO SERVICE

(IMPORTANT- INSTRUCTIONS PRIOR TO START UP)

SHIPPED WITH OIL IN GEAR BOXES

SHIPPED WITHOUT GREASE IN GREASE FITTINGS.

UNIT MUST BE SERVICED BEFORE USING.

•In Gearboxes use gear oil (type GL5 -85W 140 or Triple Zero Grease; which can be poured, and has "EP" i.e. "Extreme Pressure" additives.)

•For all Grease Fittings use TYPE/grade II tube grease.

STEP 1 Place rotary tiller so that the deck is secure and level.

STEP 2 Remove 1/2‖ Pipe Plug (Located at top of transmission gearbox). See Figure A.

STEP 3 Fill gearbox using gear oil until gearbox is approximately 1/2 full. See Figure B.

STEP 4 Replace and tighten the 1/2‖ pipe plug and clean away any excess oil. See Figure C.

STEP 5 Remove 1/2‖ Pipe Plug (Located at top of side gearbox, See Figure E on page 10) and the 1/8" check plug (Located in side of the side gearbox) if oil comes out of check plug hole, replace plug immediately and go to STEP 7. If oil doesn’t come out go to STEP 6.

8

Page 7 Page 9
Page 8
Image 8
King Kutter 999995 manual Rotary Tiller Assembly Instructions, Before Putting Rotary Tiller Into Service
Page 7 Page 9

999995 specifications

The King Kutter 999995 is a robust and reliable rotary cutter designed for both agricultural and commercial applications. Known for its durability and efficiency, it stands out as a preferred choice among landowners, farmers, and landscapers who need a dependable tool for land management and brush clearing.

One of the primary features of the King Kutter 999995 is its heavy-duty construction. Built with a rugged, all-steel frame, this rotary cutter is designed to withstand harsh conditions and perform reliably in challenging environments. The cutter’s thick side skirts and reinforced welds provide added strength and support, ensuring that it can handle tough materials like dense brush and thick grass with ease.

Another notable technology incorporated into the King Kutter 999995 is its high-performance blade system. The cutter is equipped with heavy-duty, heat-treated blades that are designed for longevity and superior cutting capability. These blades can be easily sharpened or replaced when necessary, making maintenance simple and ensuring that the cutter remains efficient over time.

The King Kutter 999995 also features a double-gearbox design, which enhances its cutting performance. This dual gear system allows for increased torque, enabling the cutter to tackle tougher materials without bogging down. The gearbox is designed for high-efficiency operation, which minimizes wear and maximizes the lifespan of the machine.

Another key characteristic of this rotary cutter is its compatibility with a wide range of tractors. The King Kutter 999995 is available in a variety of sizes and can be easily attached to both small and large tractors, making it a versatile tool for users with different equipment options. Its user-friendly design allows for quick setup and operation, making it accessible for users of all skill levels.

Safety is also a primary consideration in the King Kutter 999995 design. The cutter is equipped with safety features to minimize the risk of accidents during operation. These include a standard chain guard system that helps prevent debris from flying into the operator's area while cutting.

In summary, the King Kutter 999995 is a top-of-the-line rotary cutter that combines heavy-duty construction, advanced blade technology, and high compatibility with tractors. Its features make it an excellent choice for anyone seeking a reliable tool for land clearing and maintenance, offering both efficiency and safety for various cutting tasks.