KitchenAid 3184873 TmNow start, Electrical connection, Panel B, A. Where local codes permit

The appliance should be connected directlv to the fused disconnect or

circuit breaker dox through flexible, armored or non-metallic sheathed, copper cable (with grounding wire). Locate the junction box to allow two to three feet of slack in the line so that the range can be moved if servicing is ever necessary. Do Not cut the conduit.

A U.L.-listed conduit connector must be provided at each end of the power supply cable (at the appliance and at the junction box). Wire sizes (COPPER WIRE ONLY) and connections must conform with the rating of the appliance.

El The Tech Sheet is in a pouch attached to the left hand underside of

the oven. To access, remove the storage drawer (slide-in) or grille (drop-in).

Electrical connection

Electrical Shock Hazard

l Electrical ground is required on this appliance.

l Do Not connect to the electrical supply until appliance is permanently grounded.

l Disconnect power to the junction box before making the electrical connection.

l This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire lead on the appliance.

Failure to do so could result in a fire, personal injury or electrical shock.

This appliance is manufactured with the white (neutral) power supply wire and a cabinet-connected green grounding wire twisted together.

Connect the appliance cable to the junction box through the U.L.-listed conduit connector. Complete electrical connection according to local codes and ordinances.

A. Where local codes permit...

connecting the cabinet-grounding conductor to the neutral (white) junction box wire:

Cable from

Junction power supply

I

Bare 0Ym green wire

conduit

Figure 1 Cable from connector

range

Grounded Neutral

1.Disconnect the power supply.

2.Connect together 3 wires: green and white appliance cable wires and the neutral (white) wire in junction box.

3.Connect the two black wires together; then the two red wires together. See Figure 1.

B. Where local codes Do Not

permit...

connecting the cabinet-grounding conductor to the neutral (white) junction box wire:

Cable from

green
wires	kFZJ	L-listed
	Cable from	c&fuit
	range	connector
Figure	2

Ungrounded Neutral

1.Disconnect the power supply.

2.Separate the green and white appliance cable wires.

3.Connect the white appliance cable wire to the neutral (white) wire in the junction box.

4.Connect the two black wires together; then the two red wires together. See Figure 2.

5.Connect the green grounding wire to a grounded wire in the junction box.

C.If connecting to a four-wire

electrical system:

DO NOT connect the cabinet-grounding conductor to the neutral (white) junction box wire.

Figure 3	Cable from	conduit
	range	connector

1.Disconnect the power supply.

2.Separate the green and white appliance cable wires.

3.Connect the white appliance cable wire to the neutral (white) wire in the junction box.

4.Connect the two black wires together; then the two red wires together. See Figure 3.

5.Connect the green grounding wire to the grounding wire in the junction box.

TmNow start...

With range in kitchen.

Remove shipping materials, tape, and

II n protective film from range. Do Not remove shipping base at this time.

Remove the racks and other parts

12. from inside the oven.

Insert a nail or a 5/32” diameter item in the hole in each of the hinges. Close the door as far as possible. Lift oven door off of the hinges and set aside.

1

II

Slide-in installation: Remove storage drawer.

Drop-in installation: Remove storage drawer and the side bottom panels. Install Kit. No. 3183638 (black), 3183639 (white), or 3183640 (almond) according to the Installation Instructions packed with kit.

I Floor Damage

Before moving range across floor, check that range is on shipping base or slide range onto cardboard or hardboard.

Failure to do so could cause damage to floor covering.

15 Move range close to cabinet cutout.

. Make electrical connection. See “Electrical requirements” and “Electrical connection” sections, Panels A and B, for details.

Personal Injury Hazard

Because of the weight and size of this range, two or more people are needed to move and safely install it.

Failure to do so could result in personal injury.

Use this area to grip.

range. Lift range up to cabinet opening using the oven opening as an area to grip.

.

II

Center range in cabinet cutout. Loosen screws and insert spacers (shipped in literature bag) on each side of the control console. If range does not fit properly, check spacers. The spacers

Panel B