7
Display
When power is first supplied to the microwave oven, “0:00” will
appear in the display. Ifthe “0:00” appears in the display at any
other time, a power failure has occurred. Reset the clock if
needed. See “Clock.”
When the microwave oven is in use, the display will show cook
time remaining. When the microwave oven is not in use, the
display will show the time of day (if the clock is set) or Timer
countdown (if the Timer is set).
Start
The START control begins any function. Ifcooking is interrupted
by opening the door, touching START will resume the cycle.
NOTE: To avoid unintentional operation of the microwave oven,
a cooking function cannot be started if the microwave oven door
has been closed for about 5 minutes. The word “door” will
appear in the display until the door is opened and closed.
Add 30 Seconds
The (START) ADD 30 SEC control automatically starts the
microwave oven at 100% power for 30 seconds, and adds
30 seconds of cook time with each additional touch of the
control.
Time may be added to any manual cooking cycle in 30-second
increments, at the current power level, by touching (START) ADD
30 SEC during cooking.
NOTE: To avoid unintentional operation of the microwave oven,
a cooking function cannot be started if the microwave oven door
has been closed for about 5 minutes. The word “door” will
appear in the display until the door is opened and closed.
Stop Cancel
The STOP CANCEL control clears any incorrect command, and
cancels any program during cooking. It will not erase the time of
day.
The microwave oven will also turn off when the door is opened.
Close the door and touch START to resume the cycle.
The STOP CANCEL control is also used to lock and unlock the
control panel. See “Control Lock.”
Ton e s
Tones are audible signals that cannot be turned off, and they
indicate the following:

One tone

■Valid entry
■Control lock activated or deactivated
■End of stage in multistage cooking

Three tones

■End of Timer countdown

Five tones

■End of cycle
■Reminder, repeat each minute after the end-of-cycle tones
Clock
This is a standard 12-hour clock (1:00-12:59). The Clock cannot
be erased. If the Clock is not set, “0:00” will remain in the display
when the microwave oven is not in use.

To S et :

The microwave oven and Timer must be off.
1. Tou ch C LO CK.
2. Touch number pads to enter correct time of day.
3. Tou ch C LO CK.
Time r
The Timer can be set in minutes and seconds, up to 99 minutes
99 seconds, and counts down the set time.
NOTE: The Timer does not start or stop the microwave oven.
Cook functions may be used while the Timer is counting down.
When the cook function is active in the display, touch TIMER to
see the Timer count down for about 5 seconds.

To S et :

1. Tou ch T IM ER.
2. Touch number pads to enter desired time.
3. Touch START.
When the set time ends, “End” will appear in the display and
the end-of-Timer tones will sound.
4. Touch STOP CANCEL while the Timer is active in the display
to cancel the Timer.
Control Lock
The Control Lock disables the control panel pads to avoid
unintended use of the microwave oven.
To Lock/Unlock Control: The microwave oven must be off.
Touch and hold STOP CANCEL for about 3seconds, until the
tone sounds and the control lock icon appears in the display.
Repeat to unlock.
If any control pad is touched while the control is locked, there will
be no response from the control.
Language
The default display language is English, but may be set to
French. Two display messages are affected: “End” (English) or
“Fin” (French), and “door” (English) or “PrtE” (“porte” - French).
To Set Language to French: With the microwave oven door
open, touch and hold number pad 1 for about 5 seconds, until a
tone sounds. Repeat to change back to English.
Weight Entry Mode
The default weight entry mode for Weight Defrost is imperial
(pounds), but may be set to metric (grams). This setting does not
affect any other program besides Weight Defrost. See “Weight
Defrost/Timed Defrost” section.
To Set Weight Entry to Metric: With the microwave oven door
open, touch and hold number pad 0 for about 5 seconds, until a
tone sounds. Repeat to change back to imperial.