bracket for rear venting

WARNING

12. Disconnect power.

d. Remove screws attaching brackets to each side of blower. Reposition brackets on blower as shown. Then reinstall screws.

e. Reinstall blower in blower box with mouth of blower pointing

Excessive Weight Hazard

Use two or more people to move and install downdraft vent.

Failure to do so can result in back or other injury.

10. Insert downdraft vent into countertop cutout. Two people are recommended to support the weight of the downdraft vent

wiring box

green ground screw

conduit

out open side of blower box. Secure blower to blower box with 6 Phillips-head screws.

NOTE: Square metal frame attached to mouth of blower must be installed for proper operation.

f. Attach metal cover from parts bag over down-venting knockout in blower box. Remove rear knockout cover on back of vent base.

g. Reconnect blower wiring cable. Secure wiring cable in 2 black plastic clips inside vent base.The wiring cable must be properly secured in the 2 clips (see step b.) Reattach blower box to downdraft vent base with 4 hex nuts.

during lifting. Position downdraft vent so it is centered in cutout and parallel to edge of cutout. Check that downdraft vent is level vertically. Then fasten lower support legs to cabinet floor with screws.

When attaching undercounter bracket to underside of countertop, make sure that the screw length will not go through countertop when tightened.

11. Attach one undercounter bracket on front upper right corner of downdraft vent with slot over vent mounting hole and flange against countertop. Attach other bracket to left side of downdraft vent. Carefully drill starter holes through undercounter mounting brackets into underside of countertop. Insert appropriate length screws into holes and tighten brackets to countertop.

connector

13. Remove required knockout and install conduit connector. Feed the power supply cable through the conduit connector and into the wiring box. Connect the white wires together with a twist-on wire connector. Connect the black wires together with a twist-on wire connector. Attach the green (or green and yellow) ground wire to eyelet with green ground screw. Tighten the conduit connector clamp screws. Replace the wiring box cover.

14. Reconnect power.

microswitches behind filters.

ON/OFF button

top trim

blower control knob

filter or filters

 

depending on

end cap

model

15. Push and hold for a few seconds the button on the top of the downdraft vent. Retractable

8. Attach backdraft damper over blower box knockout with 2 Phillips-head screws.

9. Remove the 2 Phillips-head screws attaching the wiring box cover. Determine which direction (rear or down) electrical connection will need to run from appliance wiring box. Remove rear or bottom knockout and install conduit connector.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Connect ground wire to green ground screw in terminal box.

Failure to do so can result in death or electrical shock.

section of downdraft vent will rise and blower will start. Position the top trim over the retractable section and snap trim into place.

8

Page 7 Page 9
Page 8
Image 8
KitchenAid KPEU722M installation instructions Bracket for rear venting
Page 7 Page 9

KPEU722M specifications

The KitchenAid KPEU722M is a versatile and innovative kitchen appliance designed to elevate your culinary experiences. Renowned for its durability and performance, this appliance embodies KitchenAid’s commitment to quality and user-friendly design.

One of the standout features of the KPEU722M is its powerful motor, which delivers excellent performance across various cooking tasks. Whether you are kneading dough, whipping cream, or mixing batters, this kitchen tool can handle it all with ease. The motor is designed for both efficiency and longevity, ensuring that it can withstand the demands of regular use in a busy kitchen.

Another key characteristic of the KPEU722M is its advanced planetary mixing action. This unique technology allows the mixing bowl to rotate while the beater moves in the opposite direction. As a result, all ingredients are thoroughly mixed and incorporated, delivering consistent results every time. This feature is particularly beneficial when making bread or chiffon cake, where uniform blending is essential.

In terms of design, the KPEU722M boasts an elegant and modern aesthetic that can complement any kitchen decor. It is available in various colors, allowing users to choose one that best fits their style. The appliance is also engineered for ease of use, with intuitive controls that provide a seamless user experience.

The KPEU722M comes with a range of attachments, including a flat beater, dough hook, and wire whip, further enhancing its versatility. Each attachment is designed to cater to specific tasks, enabling users to experiment with different recipes and techniques. Additionally, the bowl is spacious, allowing for large batches to be prepared at once, making it ideal for family gatherings or baking marathons.

Safety features are another hallmark of the KPEU722M. It incorporates a thermal overload protection system that protects the motor from overheating, ensuring the appliance operates safely during extended use. Furthermore, the non-slip base provides stability while mixing, preventing any accidents.

Overall, the KitchenAid KPEU722M is a powerful and stylish kitchen appliance that brings advanced mixing technology and convenience to the home cook. With its robust performance, thoughtful design, and essential features, it is a valuable addition to any kitchen, ideal for both novice chefs and seasoned professionals.
Top Page Image Contents