KitchenAid KUDE70FVSS0 warranty Controls Cycle Status Control Purpose Comments

You can customize your cycle by selecting an option.

See option selections. If you change your mind, press the option again to turn off the option, or select a different option. You can change an option anytime before the selected option begins.

*Maximum wash times depend on water temperature, heavy soil condition, dish load size and options selected.

OPTION SELECTIONS

OPTIONS	DISH LOAD TYPES	DESCRIPTIONS	USE WITH:
	Pans, casseroles, etc. with	Activates the PROSCRUB® spray jets and provides	Heavy Duty or Normal
	tough food soil.	intensified water spray to the back of the lower level rack.	cycle
		May add heat and time to the cycle.

To sanitize your dishes and glassware in accordance with NSF/ANSI Standard 184 for Residential Dishwashers.

Raises the water temperature in the final rinse to approximately 155°F (68°C). This high temperature rinse sanitizes your dishes and glassware in accordance with NSF/ANSI Standard 184 for Residential Dishwashers. Certified residential dishwashers are not intended for licensed food establishments.

The Sanitize or Sani Rinse option adds heat and time to the cycle.

Normal cycle. Heavy Duty cycle automatically uses Sani Rinse. Only these sanitization cycles have been designed to meet the NSF/ANSI requirements.

	Loads containing tough,	Increases the target water temperature during the wash	Heavy Duty or Normal
	baked-on food.	portions of the cycle.	cycles
		Adds heat, wash time and water to the cycle.
	For best drying results, dry	Turn OFF when loads contain plastic dinnerware that may be	All cycles, except Rinse
	dishes with heat.	sensitive to high temperatures.	Only. Automatic with all
		This option with the use of rinse aid will provide the best	wash cycles unless you
			turn it off.
		drying performance.
	To run your dishwasher at	Delays the start of a cycle up to 4 hours.	All cycles, except Rinse
	a later time or during off-	Select a wash cycle and options. Press 4 Hour Delay. Press	Only
	peak hours.
		START/RESUME. Close the door firmly.
Control Lock To avoid unintended use of		To turn on Lock, press and hold Heat Dry for at least	Anytime
	your dishwasher, or cycle	4 seconds.
	and option changes during	To turn off Lock, press and hold Heat Dry for at least
	a cycle.
		4 seconds.
		When Control Lock is lit, all buttons are disabled. If you press
		any pad while your dishwasher is locked, the light flashes
		3 times. The dishwasher door can be opened while the
		controls are locked.

IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the cycle for the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle will automatically compensate by adding time, heat and water as needed.

CONTROLS AND

CYCLE STATUS

CONTROL PURPOSE COMMENTS

To start or resume a wash cycle

If the door is opened during a cycle or the power is interrupted, the START/RESUME indicator flashes. The cycle will not resume until the door is closed and START/RESUME is pressed.

NOTE: If the START/RESUME button is located on top of door, push door firmly closed within 3 seconds of pressing START/RESUME.

To cancel wash	Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let the dishwasher
cycle	drain completely.

To follow the progress of your dishwasher cycle

The Clean indicator glows when a cycle is finished.

If you select the Sani Rinse option, when the Sani Rinse cycle is finished, the Sanitized indicator glows. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This can happen if the cycle is interrupted, or the water could not be heated to the required temperature. The light goes off when you open and close the door or press CANCEL.

5