KitchenAid KUDP01FL Canceling a Cycle, Changing a Cycle or Setting, Adding Items During a Cycle

		Use this cycle for pre-
		rinsed and lightly-soiled
		loads. During the heated				Use main
		dry, the heating element
		cycles on and off.				detergent
						dispenser section.
Soil	Rinse	Main	Rinse	Purge†	Final	Dry	Time	Water
Level		Wash			Heated		(min)	Usage
Sensed					Rinse			(gal/L)
	●	●	●		●	●	79*	7.1-8.6/
Heavy		120°F			135°F	cycled		27-33
		(49°C)			(57°C)
	●	●		●	●	●	71*	5.9/
Light		120°F			135°F	cycled		22.3
		(49°C)			(57°C)
		Use this rinse cycle for
		rinsing dishes, glasses, and
		silverware that will not be				Do not use
		washed right away.
						detergent with this
						cycle.
Soil	Pre-	Main	Rinse	Rinse	Final	Dry	Time	Water
Level	Wash	Wash			Heated		(min)	Usage
Sensed					Rinse			(gal/L)
				●			10	1.8/7

†A small amount of water is run through the pump to remove soil particles between the main wash and final rinse.

NOTES:

■The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary from the numbers above as the sensor adjusts the cycle for the best wash performance.

■In the Normal cycle, the dishwasher pauses while soaking. Soaking helps loosen soils on dishes for brilliant results.

Canceling a Cycle

1.Carefully open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door to access the control panel.

2.Press

Changing a Cycle or Setting

During the first minute of a cycle

1.Open the door.

2.Press a new cycle and/or options.

3.Check the detergent dispensers. They must be filled properly for the new cycle.

4.Close the door. The dishwasher resumes the new cycle and/or option after a 5-second pause.

After the first minute of a cycle

1.Carefully open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door to access the control panel.

2.Press

Cancel glows.

3.Close the door. Your dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely.

4.Select a new cycle and/or options.

5.Press START.

6.Check the detergent dispensers. They must be filled properly for the new cycle.

7.Close the door.

Adding Items During a Cycle

You can add an item anytime before the main wash starts. Open the door and check the detergent dispenser. If the cover is still closed, you can add items.

To add items

1.Carefully open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door.

2.Open the door. If the detergent dispenser cover is still closed, add the item.

3.Close the door firmly until it latches. The dishwasher resumes the cycle after about a 5-second pause.

Cancel glows.

3.Close the door. The dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely.

To stop the drain

You can press CANCEL again to stop the drain. Remember to drain the dishwasher before starting a new cycle.

To clear the indicators

Press CANCEL before starting the dishwasher to clear all options and cycles.

Option Selections

You can customize your cycles by pressing an option. If you change your mind, press the option again to turn the option off. Select a different option if desired.

You can change an option anytime before the selected option begins. For example, you can press an unheated drying option any time before drying begins.

Press START to repeat the same cycle and options as the previous wash cycle.

NOTE: If the last cycle you completed was a rinse cycle, when you press Start, the dishwasher runs the last full wash cycle and options.

12