INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
■ If you are installing the junction box on rear wall behind the |
microwave oven, the junction box must be recessed and |
located in the upper or lower right or left corner of the cabinet; |
otherwise, the microwave oven will not fit into the cabinet |
opening. |
■ Microwave oven support surface must be solid, level and flush |
Tools needed
■Phillips screwdriver
■
■Measuring tape
■Level
■Drill (for wall cabinet installations)
■¹⁄₈" (3 mm) drill bit (for wall cabinet installations)
■1" (2.5 cm) drill bit (for wall cabinet installations)
with bottom of cabinet cutout. Floor must be able to support a |
weight of 90 lbs (41.0 kg). |
IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).
Parts needed
■A UL listed or CSA approved conduit connector
■UL listed wire connectors
Parts supplied
AC D
B
A. Spacer bars (2)
B. Bottom vent (1)
C. ³⁄₈" hex washer head screws (4)
D. ¾" pan head screws (4)
Check local codes. Check existing electrical supply. See “Electrical Requirements.”
It is recommended that all electrical connections be made by a licensed, qualified electrical installer.
Product Dimensions
27" (68.6 cm) and 30" (76.2 cm) Microwave Ovens
A
B
E
D | C |
| |
27" (68.6 cm) models | 30" (76.2 cm) models |
A. 25⁵⁄₈" (65.1 cm) recessed width | A. 25⁵⁄₈" (72.7 cm) recessed width |
B. 18⁵⁄₈" (47.3 cm) overall height | B. 18⁵⁄₈" (47.3 cm) overall height |
C. 26³⁄₄" (68.0 cm) overall width | C. 29³⁄₄" (75.6 cm) overall width |
D. 22³⁄₄" (57.8 cm) overall depth | D. 22³⁄₄" (57.8 cm) overall depth |
E. 17¹⁄₄" (43.8 cm) recessed height | E. 17¹⁄₄" (43.8 cm) recessed height |
27" (68.6 cm) and 30" (76.2 cm) Microwave Oven Spacer Kit
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance with microwave oven.
■Recessed installation area must provide complete enclosure around the recessed portion of the microwave oven.
■Grounded electrical supply is required. See “Electrical Requirements” section.
■Electrical supply junction box should be located 3" (7.6 cm) maximum below the support surface when the microwave oven is installed in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the left rear corner of the support surface to pass the appliance cable through to the junction box.
■For installation above single
A
27" (68.6 cm) models | 30" (76.2 cm) models |
A. 26³⁄₄" (67.9 cm) | A. 29³⁄₄" (75.6 cm) |
overall width | overall width |
NOTE: The microwave oven spacer kit will allow the microwave oven to be installed in a
A microwave oven spacer kit is available from your dealer that will allow the microwave oven to be installed in a 19"- 19¹³⁄₁₆"
27" (68.6 cm) Stainless Steel - Model W10469901 30" (76.2 cm) Stainless Steel - Model W10469903
To order, see the “Assistance or Service” section of the Use and Care Guide.
2